CrimeStopper EZ-45DP/55DP страница 3 Скачать руководство пользователя

Страница: 3 / 32

INSTALLATION CAUTIONS & WARNINGS

**FOR SAFETY REASONS, DO NOT INSTALL in vehicles with MANUAL TRANSMISSIONS

.** If accidentally left in

gear, a remote started vehicle could become a self-propelled threat to life and property.

DO NOT

extend the Remote start ignition harness length. Mount the module so that main harness reaches all ignition

switch wiring. Extending these wires could result in poor or improper performance.

DO NOT

route any wiring that may become entangled with brake, gas pedals, steering column or any other moving parts

in the vehicle.

DO NOT

exceed the rated output current of any circuit on the Remote start module. Failure to observe this warning will

result in damage to the unit not covered under warranty.

DO NOT

remote start the vehicle in a closed garage! Make sure that the garage door is open or there is adequate

ventilation. Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes.

PROGRAM/OVERIDE SWITCH AND LED

PROGRAM/OVERRIDE SWITCH: 2 PIN PLUG (REQUIRED FOR PROGRAMMING & LEARNING REMOTES)

This switch is used for programming features, transmitters, valet mode, and to override the optional starter disable (if
installed) in the event of a non-operating remote control.

LED: 2 PIN PLUG (OPTIONAL)

The LED is used as a VALET/PROGRAMMING indicator and it will also FLASH for use as security deterrent when
Remotely Locking the door.

VALET / PROGRAM SWITCH

STATUS LED

Содержание EZ-45DP/55DP

































Результаты поиска

Содержание EZ-45DP/55DP

Отзывы:

Похожие инструкции для EZ-45DP/55DP

Бренды по названию

Популярные бренды

CrimeStopper EZ-45DP/55DP, Руководство по установке

Результаты поиска

Содержание EZ-45DP/55DP

Отзывы:

Похожие инструкции для EZ-45DP/55DP

Бренды по названию

Популярные бренды