CrimeStopper EZ-45DP/55DP страница 25 Скачать руководство пользователя | Manualshive

Страница: 25 / 32

background image

25

OPTIONS PROGRAMMING Cont.

24. Option Reset:

(RESTORE TO DEFAULT FOR EZ-45DP II ONLY)

on pages 20-21

This option allows you to restore all programmable options to factory default values. Go to the option 24 and press the
Unlock Button #2 on the remote. The lights flash 2 times and all values will be reset to factory original settings.

OPTIONS PROGRAMMING FOR EZ-55 AND EZ-95 ONLY

FOR EZ-55 AND EZ-95 ONLY

24. Aux #3:

This option controls the function of the Violet wire for a negative output for a Momentary, Pulse, Timed or Latched
output, depending on option used. Option #25 controls the length of time output.

25. Aux #3 Time control: (1 sec. to 255 sec.) Default = 12 seconds

This option determines to length of time that is outputted from Aux #3 (Violet wire). Pressing the Lock or Unlock buttons
on the remote raises or lowers the time by one second.

26. Aux #4:

This option controls the function of the Violet/White wire for a negative output for a Momentary, Pulse, Timed or
Latched output, depending on option used. Option #27 controls the length of time output.

27. Aux #4 Time control: (1 sec. to 255 sec.) Default = 12 seconds

This option determines to length of time that is outputted from Aux #4 (Violet/White wire). Pressing the Lock or Unlock
buttons on the remote raises or lowers the time by one second.

28. Option Reset:

(RESTORE TO DEFAULT FOR EZ-55 AND EZ-95)

on pages 20-21

This option allows you to restore all programmable options to factory default values. Go to the option 28 and press the
Unlock Button #2 on the remote. The lights flash 2 times and all values will be reset to factory original settings. Default
values are marked with asterisks in the chart on pages 20-21.

«
...
23
24
25
26
27
...
»

Содержание EZ-45DP/55DP

































Отзывы:

Нет отзывов

Похожие инструкции для EZ-45DP/55DP

Бренд: Omnex Страницы: 9

Бренд: Niko Страницы: 2

BC JUMPSTARTER SUPERCAP HYBRID 12V-3200A

Бренд: Battery Controller Страницы: 5

Бренд: REMdevice Страницы: 14

Бренд: Raymarine Страницы: 34

Бренд: Nuvera Страницы: 9

Бренд: Rotel Страницы: 96

ConnectLine App

Бренд: oticon Страницы: 18

System THREE SH

Бренд: Premier Defense Страницы: 10

Бренд: FUTABA Страницы: 2

ECO-i RCS-SH1AAB

Бренд: Sanyo Страницы: 1

ECO-i RCS-TRP80AAB.WL

Бренд: Sanyo Страницы: 1

Glow Keys RMT-U130

Бренд: Sanyo Страницы: 2

Бренд: Sanyo Страницы: 8

ECO-i RCS-TM80BG

Бренд: Sanyo Страницы: 16

Бренд: Photron Страницы: 93

Бренд: Marmitek Страницы: 32

Бренд: HeathZenith Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды