CrimeStopper EZ-45DP/55DP Скачать руководство пользователя | Manualshive

Страница: 1 / 32

background image

EZ-45DP/55DP 1 WAY SYSTEMS

EZ-95FM 2-WAY SYSTEM

DP SERIES II (Data port)

REMOTE ENGINE STARTING SYSTEM

INSTALLATION INSTRUCTIONS

INTRODUCTION

CONGRATULATIONS

on your choice of a “EZEE Start” System by Crimestopper Security Products Inc. This booklet

contains the information necessary for installing your remote starter system. If any questions arise, contact your
installation dealer or Crimestopper Security Products Inc. at the Tech Support number below.

DISCLAIMER:
This installation book is designed for the installer or individual with an existing understanding of automotive electrical
systems, along with the ability to test and connect wires for proper operation.  To ease installation, we suggest that you
READ THIS MANUAL before beginning your installation.  This book is provided as a GENERAL GUIDELINE and the
information contained herein may differ from your vehicle.  Crimestopper Security Products, Inc. and its’ vendors shall not
be liable for any accident resulting from the use of this product.  This system is designed to be professionally installed into
a vehicle in which all systems and associated components are in perfect working condition.

TECHNICAL SUPPORT: (800) 998-6880

Monday - Friday 8:00am - 4:30pm Pacific Std. Time
Web Site: www.crimestopper.com
E-mail: [email protected]

CRIMESTOPPER SECURITY PRODUCTS, INC.
1770 S. TAPO STREET, SIMI VALLEY, CA. 93063

REV C 09.2006

This device complies with FCC Rules part 15.  Operation is subject to
the following two conditions:  (1) This device may not cause harmful
interference, and (2) This device must accept any interference that
may be received, including interference that may cause undesired
operation.  The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment.
Such  modification  could  void  the  user’s  authority  to  use  the
equipment.

1
2
3
...
»

Содержание EZ-45DP/55DP

































Отзывы:

Нет отзывов

Похожие инструкции для EZ-45DP/55DP

Slim Remote Control

Бренд: Packard Bell Страницы: 2

Бренд: Daikin Страницы: 19

Бренд: GE Страницы: 32

Бренд: Autopage Страницы: 33

Бренд: Marantz Страницы: 20

Бренд: La Crosse Technology Страницы: 1

Бренд: VOLTIMA Страницы: 52

Mighty Seven FA-1214

Бренд: King Tony Страницы: 8

Бренд: King Tony Страницы: 36

Бренд: Eaton Страницы: 36

RCR504BR Series

Бренд: RCA Страницы: 3

Бренд: ZIGBEE Страницы: 43

Бренд: dewert okin Страницы: 4

ergomotion RF406

Бренд: dewert okin Страницы: 4

Бренд: Beka LED Страницы: 6

Бренд: One for All Страницы: 56

Бренд: One for All Страницы: 76

Бренд: Targus Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды