Crestron Green Light GL-IPAC-SW8 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 45

background image

15 • GL-IPAC-SW8

Product Manual — Doc. 7389C

⑥

SENSORS 1-4 24, 1 - 4, G connects to occupancy sensors. Use 18 - 12 AWG wiring.

SENSORS 5-8 24, 1 - 4, G connects to photocells. Use 18 - 12 AWG wiring.

24 supplies power to the devices and should be daisy chained to all devices in the same
sensor group.

1 - 4 control signal from the connected devices.

G is the common ground to the devices and should be daisy chained to all devices on the
same sensor group.

Occupancy Sensor Wired to SENSORS 1-4 Port

Occupancy sensors can only be wired to the SENSORS 1-4 port.

«
...
13
14
15
16
17
...
»

Содержание Green Light GL-IPAC-SW8














































Отзывы:

Нет отзывов

Похожие инструкции для Green Light GL-IPAC-SW8

Бренд: 3M Страницы: 34

Бренд: Barco Страницы: 6

Бренд: Barco Страницы: 4

Бренд: Camozzi Страницы: 33

Бренд: Camozzi Страницы: 2

Бренд: Camozzi Страницы: 64

VLT AutomationDrive FC 302

Бренд: Danfoss Страницы: 128

VLT DriveMotor FCP 106

Бренд: Danfoss Страницы: 4

Бренд: National Instruments Страницы: 29

Бренд: Watts Страницы: 24

Бренд: Ultraflex Страницы: 7

Бренд: BendPak Страницы: 43

Бренд: RKC INSTRUMENT Страницы: 10

OPTISWITCH 5100 C

Бренд: KROHNE Страницы: 40

Бренд: Belimo Страницы: 2

Бренд: Watts Страницы: 12

ZoneSense Plus AS

Бренд: Halma Страницы: 58

PARTNER II Release 4.1

Бренд: Lucent Technologies Страницы: 363

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды