background image

 

4  

  DMF-CI-8: DM NVX and DMCF Card Chassis 

Supplemental Guide – DOC. 7861C 

LCD Display Operation 

The LCD display provides menus that allow card and DMF-CI-8 chassis status 

information to be displayed. In addition, menus are provided that allow configuration of 

the cards and the chassis.  

When the DMF-CI-8 is powered on and whenever the LCD display is in an idle state, a 

general information screen appears on the LCD display.  

Sample General Information Screen 

Chassis Status:  OK         

Card:     1 

Model: DM-NVX-350C 

Name: Podium 

IPv4:    192.168.123.123 

 

 

 

The general information screen displays the following information: 

 

Chassis Status: OK 

 

Card: Slot number of the DMF-CI-8 into which a card is installed 

NOTE: 

The LCD display provides information about each card slot on a  

scrolling basis. 

 

Model: Model of the card 

 

Name: Name assigned to the card using the DM NVX web interface or SIMPL 

programming (for example, Podium, as shown in the sample general information 

screen above). If a name is not assigned, the display shows the hostname of the 

card. If a card is not installed in the slot, the display indicates Not Installed. 

 

IPv4: IPv4 (Internet Protocol version 4) address of the card 

To navigate the LCD display menus and to adjust settings, use the front panel controls. 

The controls consist of the navigation pad, the HOME push button, and the BACK push 

button. The following illustration shows the front panel controls. 

Front Panel Controls 

 

Left

Right

Select

Up

Down

HOME
BACK

Содержание DMF-CI-8































Отзывы: