DM-RMC-SCALER-C
DigitalMedia 8G+
™
Receiver & Room Controller w/Scaler
crestron.com
|
800.237.2041
MODELS & ACCESSORIES
Available Models
DM-RMC-SCALER-C:
DigitalMedia 8G+
™
Receiver & Room Controller
w/Scaler
Included Accessories
PW-2407WU:
Wall Mount Power Pack 24VDC, 0.75A, Universal
(Qty. 1 included)
Available Accessories
DM-CBL-8G-NP:
DigitalMedia 8G
™
Cable, non-plenum
DM-CBL-8G-P:
DigitalMedia 8G
™
Cable, plenum
DM-8G-CONN:
DigitalMedia 8G
™
Cable Connector
DM-8G-CRIMP:
Crimping Tool for DM-8G-CONN
DM-8G-CONN-WG:
DigitalMedia 8G
™
Cable Connector with Wire Guide
DM-8G-CRIMP-WG:
Crimping Tool for DM-8G-CONN-WG
CBL Series:
Crestron
®
Certified Interface Cables
MP-WP Series:
Media Presentation Wall Plates
MPI-WP Series:
Media Presentation Wall Plates - International Version
CNSP-XX:
Custom Serial Interface Cable
IRP2:
IR Emitter Probe w/Terminal Block Connector
USB-EXT-DM:
USB Extenders
Notes:
1. For DM 8G+ or HDBaseT wiring, use Crestron
DM-CBL-8G
DigitalMedia 8G Cable, Crestron
DM-CBL
DigitalMedia Cable, Crestron
DM-CBL-D
DigitalMedia D Cable, or third-party CAT5e
(or better) UTP or STP. Maximum wire length for DM 8G+ is 330 ft (100 m) between devices.
Shielded cable and connectors are recommended to safeguard against unpredictable
environmental electrical noise which may impact performance at resolutions above 1080p.
Refer to the
Crestron DigitalMedia Design Guide, Doc. #4546
for complete system design
guidelines. DM 8G+ is compatible with HDBaseT Alliance specifications for connecting to
HDBaseT compliant equipment. All wire and cables sold separately.
2. Automatically passes 3D video if display device supports it (reverts to pass-through mode
without scaling). Provides automatic 3D-to-2D conversion (with scaling) if display device does
not support 3D.
3. The HDMI output requires an appropriate adapter or interface cable to accommodate a DVI
signal.
CBL-HD-DVI
interface cables are available separately.
4. EDID (Extended Display Identification Data) is data embedded in an HDMI, DVI, or VGA signal
that enables a display device to tell the source device what resolutions and formats it can
support, allowing the source to configure itself automatically to feed the best signal that both
devices can support.
5. Compatible with Crestron USB-EXT-DM-LOCAL and USB-EXT-DM-REMOTE USB extender
modules, sold separately.
6. Video wall processing requires a separate DM-RMC-SCALER-C for each individual display.
7. With or without reduced blanking.
8. With reduced blanking only.
This product may be purchased from an authorized Crestron dealer. To find a dealer, please
contact the Crestron sales representative for your area. A list of sales representatives is available
online at
www.crestron.com/salesreps
or by calling 800-237-2041.
The specific patents that cover Crestron products are listed online at:
patents.crestron.com
.
Crestron, the Crestron logo, Crestron Toolbox, DigitalMedia, DigitalMedia 8G, DigitalMedia 8G+,
DM, DM 8G, and DM 8G+ are either trademarks or registered trademarks of Crestron Electronics,
Inc. in the United States and/or other countries. Dolby and Dolby Digital are either trademarks or
registered trademarks of Dolby Laboratories in the United States and/or other countries. DTS and
DTS-HD Master Audio are either trademarks or registered trademarks of DTS, Inc. in the United
States and/or other countries. HDBaseT and the HDBaseT Alliance logo are either trademarks or
registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI
and the HDMI Logo are either trademarks or registered trademarks of HDMI Licensing LLC in the
United States and/or other countries. Other trademarks, registered trademarks, and trade names
may be used in this document to refer to either the entities claiming the marks and names or their
products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron
is not responsible for errors in typography or photography. Specifications are subject to change
without notice. ©2014 Crestron Electronics, Inc.
