DO
GUIDE
DO
Complete the Connections
Make additional connections as appropriate for the application.
DM-RMC-200-S and DM-RMC-200-S2
Front Panel Connections
DM-RMC-200-S Rear Panel Connections
DM-RMC-200-S2 Rear Panel Connections
DO
Set the IP Address
The configuration of the receiver within the DigitalMedia 8G™
system determines how the IP address of the receiver is set:
• If the receiver connects to a DigitalMedia™ switcher, the
receiver is configured by the switcher automatically.
• If the receiver connects to a DigitalMedia 8G fiber
transmitter, the receiver uses its own configuration
settings. By default, DHCP (Dynamic Host Configuration
Protocol) is enabled. If it is desired, assign the default IP
address to the receiver by holding down the
SETUP
button
while the unit boots up. The default IP address overwrites
the current setting. The default IP address of the DM-
RMC-200-S and DM-RMC-200-S2 is 192.168.1.248.
To manually set a different IP address, use Crestron
Toolbox™ application.
DOC. 7810B (2044421) 09.16
Specifications subject to change without notice.
DO
Learn More
Visit the website for additional information and the
latest firmware updates. To learn more about this
product, use a QR reader application on your mobile
device to scan the QR images.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the products have been tested and found to comply with specifications for CE marking.
This product is Listed to applicable UL Standards and requirements by Underwriters Laboratories Inc.
Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION:
Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Industry Canada (IC) Compliance Statement
CAN ICES-3(A)/NMB-3(A)
The products are class 1 laser products. They comply with safety regulations of IEC-60825-1, FDA 21 CFR
1040 11 and FDA 21 CFR 1040 10.
WARNING:
Visible and invisible laser radiation when open. Avoid direct exposure to beam.
NOTE:
Plug the included dust cap into the optical transceiver when the fiber optic cable is unplugged.
WARNING:
These are Class A products. In a domestic environment these products may cause radio interference in which case the
user may be required to take adequate measures.
The specific patents that cover Crestron products are listed at
patents.crestron.com
.
The product warranty can be found at
www.crestron.com/warranty
.
Certain Crestron products contain open source software. For specific information, please visit
www.crestron.com/opensource
.
Crestron, the Crestron logo, Crestron Toolbox, DigitalMedia, DigitalMedia 8G, and DM are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States
and/or other countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. UL and the UL logo are
either trademarks or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be
used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is
not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2016 Crestron Electronics, Inc.
DM-RMC-200-S
DM-RMC-200-S2
AUDIO OUT R, L
(SPEAKER):
Amplified stereo
audio output
LAN:
10BASE-T/100BASE-TX
Ethernet to local
network device
AUDIO OUT R, L (LINE):
Stereo unbalanced
line level audio output
DM IN MMF/SC:
From DM
®
switcher, transmitter,
or other DM device
24 V 2.0A MAX:
From power pack
(included)
AUDIO OUT R, L
(SPEAKER):
Amplified stereo
audio output
AUDIO OUT R, L (LINE):
Stereo unbalanced
line level audio output
LAN:
10BASE-T/100BASE-TX
Ethernet to local
network device
DM IN SMF/LC:
From DM switcher, transmitter,
or other DM device
24 V 2.0A MAX:
From power pack
(included)
DIG IN:
software
programmable
digital input
HDMI OUT:
HDMI
®
digital
video/audio
output
USB HID:
From USB
HID-compliant
device
COM:
To/from
RS-232 device
IR:
To IR
controllable
device
