background image

 
 
 

This document was prepared and written by the Technical Documentation department at: 

 

 

 

 

Important Safety Instructions

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance 
with the manufacturer's instructions.

Do not install near any heat sources such as radiators, heat 
registers, stoves, or other apparatus (including amplifiers) that
produce heat.

Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than 
the other. A grounding-type plug has two blades and a third
grounding prong. The wide blade or the third prong are 
provided for your safety. If the provided plug does not fit into 
your outlet, consult an electrician for replacement of the 
obsolete outlet.

Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the point 
where they exit from the apparatus.

Only use attachments/accessories specified by the 
manufacturer.

Use only with the cart, stand, tripod, bracket or 
table specified by the manufacturer or sold with 
the apparatus. When a cart is used, use caution 
when moving the cart/apparatus combination to 
avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused 
for long periods of time.

Refer all servicing to qualified service personnel. Servicing is 
required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been 
spilled or objects have fallen into the apparatus, the apparatus 
has been exposed to rain or moisture, does not operate 
normally, or has been dropped.

Disconnect power prior to connecting or disconnecting
equipment.

Do not install in direct sunlight.

The apparatus must be installed in a way that the power cord 
can be removed either from the wall outlet or from the device 
itself in order to disconnect the mains power.

Prevent foreign objects from entering the device.

The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPARATUS TO RAIN OR 
MOISTURE. THE APPARATUS SHALL NOT BE 
EXPOSED TO DRIPPING OR SPLASHING. OBJECTS
FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD
NOT BE PLACED ON THE APPARATUS.

WARNING:

TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE
COVER. THERE ARE NO USER SERVICEABLE PARTS 
INSIDE. ONLY QUALIFIED SERVICE PERSONNEL 
SHOULD PERFORM SERVICE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR

IMPORTANT

This device can be used with Class 2 output wiring.

 
 

This device includes an aggregation of separate independent works that are each generally copyrighted by Crestron Electronics, Inc., with all rights 

reserved. One of those independent works, Linux Bridge Project, is copyrighted under the GNU GENERAL PUBLIC LICENSE, Version2, 

reproduced in “GNU General Public License” on page 30, where the corresponding source code is available at: 

ftp://ftp.crestron.com/gpl

 
 

The specific patents that cover Crestron products are listed at patents.crestron.com. 

 

Crestron, the Crestron logo, Crestron e-Control, Crestron Toolbox, DigitalMedia, DigitalMedia 8G, DigitalMedia 8G+, DM, DM 8G, and 

DM 8G+ are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Dolby and 

Dolby Digital are either trademarks or registered trademarks of Dolby Laboratories in the United States and/or other countries. DTS and 

DTS-HD Master Audio are either trademarks or registered trademarks of DTS, Inc. in the United States and/or other countries. HDBaseT 

and the HDBaseT Alliance logo are either trademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other 

countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or 

other countries.  Windows is either a trademark or registered trademark of Microsoft Corporation in the United States and/or other 

countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming 

the marks and names or their products. Crestron disclaims proprietary interest in the marks and names of others. 

©2012 Crestron Electronics, Inc. 

Содержание DigitalMedia 8G+ DM-RMC-100-C









































Отзывы: