Crestron CNX-BIPAD8 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 32

Crestron CNX-BIPAD8 Скачать руководство пользователя страница 7

Crestron

CNX-BIPAD8

Professional Audio Distribution Processor

Operations Guide – DOC. 8160A

Professional Audio Distribution Processor: CNX-BIPAD8

•

3

Specifications

Specifications for the CNX-BIPAD8 are listed in the following table.

CNX-BIPAD8 Specifications

SPECIFICATION DETAILS

Power Requirements

20 Watts (0.83 Amp @ 24 VDC)

Default NET ID

44

Control System Update Files

1, 2, 3

2-Series Control System Update

File

CNMSX-AV/Pro

Update

File

CNRACKX/-DP

Update

File

ST-CP Update File
CEN/CN-TVAV

Update

File

Version 2.004.CUZ or later

Version 5.12.63X.UPZ or later
Version 5.12.63W.UPZ or later
Version 4.02.4S.UPZ or later
Version 5.12.63V.UPZ or later

CNX-BIPAD8 Firmware

Bipad-22.upg

RCA input ports (labeled 1 – 16)

RCA jacks – Sixteen sets of four: two for left and right
audio; two for stereo loop-through.

RCA output ports (labeled ROOMS) RCA jacks – Eight pairs for left and right preamplified (line

level) audio for corresponding room power amplifiers.

CAT5 I/O ports (labeled ROOMS)

RJ-45 Jacks – Eight shielded jacks for balanced line
audio to/from remote locations; one CAT5 stereo input
and output per connector.

Tone specifications (per channel)

Flatness (8 to 60 KHz flat mode) ±0.2 dB
Bass gain range (100 Hz)

±12 dB

Bass step size (100 Hz)

2 dB

Treble gain range (10 KHz)

±12 dB

Treble step size (10 KHz)

2 dB

Preamp specifications (per channel) Input impedance

47K Ohms

Total harmonic distortion (THD) <0.02%
S/N ratio

>100 dB

Maximum input level (flat mode) 3.2 Vrms
Maximum output level

2.5 Vrms

Channel separation

>90 dB

Gain range (excluding mute)

-80 dB to +20 dB

Volume steps

100 (1 dB/step)

Mute

> 120 dB (relay)

100 dB (electronic mute)

Rack space required

2U high, 1U wide

Environmental temperature

41° to 122°F (5° to 50°C)

Humidity

10% to 90% RH (non-condensing)

Dimensions

Height: 3.47 in (8.81 cm)
Width:

17.10 in (43.43 cm)

Depth:

8.44 in (21.44 cm)

Weight

6.2 lb (2.8 kg)

1.

The latest versions can be obtained from the Downloads | Software Updates section of the Crestron
website (www.crestron.com). Refer to NOTE on the next page.

2.

Crestron 2-Series control systems include the AV2, CP2, CP2E, MP2, MP2E, PAC2, PRO2, and
RACK2.

3.

CNX update files are required for either CNMSX-AV/Pro or CNRACKX/-DP. Filenames for CNX
update files have a UPZ extension and are in one EXE or zipped UPZ file. To avoid program problems,
make certain you are using the update file with the correct suffix letter (e.g., S, V, W, X).

«
...
5
6
7
8
9
...
»

Содержание CNX-BIPAD8

































Отзывы:

Нет отзывов