Crestron CNX-BIPAD8 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 32

Crestron CNX-BIPAD8 Скачать руководство пользователя страница 10

Professional Audio Distribution Processor

Crestron

CNX-BIPAD8

6

•

Professional Audio Distribution Processor: CNX-BIPAD8

Operations Guide - DOC. 8160A

ROOMS

The eight, shielded RJ-45 connectors provide for balanced line audio to/from remote
locations in the facility; one CAT5 stereo input and output per connector. Signal
connections for the jacks are given in the following table.

Pin #

Signal

1

Audio In L +

2

Audio In L -

3

Audio In R +

4

Audio Out L -

5

Audio Out L +

6

Audio In R -

7

Audio Out R +

8

Audio Out R -

NOTE:

For additional information on audio/video connections over CAT5, refer to

the latest version of the Crestron CAT5 Wiring Reference Guide (Doc. 6137) which
is available from the Downloads | Product Manuals section of the Crestron website
(www.crestron.com).

The eight pairs of RCA jacks output pre-amplified (line-level) and volume/tone
processed audio to corresponding room power amplifiers. Each room output contains
left and right audio channels. (These are the same signals as the unprocessed outputs
from the CAT5 connectors.)

1 – 16 (Source Connectors)

The sixteen sets of four RCA jacks connect independent audio sources to the CNX-
BIPAD8. Of each set, two of the connectors are used for left and right audio
channels; the other two are parallel stereo loop-throughs.

(Chassis Ground)

Use this chassis screw to connect the audio source(s) common ground(s) to the
CNX-BIPAD8.

Indicators

Ten LED indicators on the front panel indicate the unit’s current status.

CNX-BIPAD8 Indicators

ROOMS

4

2

5

3

8

7

6

1

NET

P WR

P R O F E S S I O N A L A U D I O D I S T R I B U T I O N P R O C E S S O R

CRESTRON

CNX-BIPAD8

PWR (Power)

This LED illuminates when 24 volts DC is supplied to the CNX-PAD8.

JACK, REAR VIEW

(TAB POSITION DOWN)

Pin 1

«
...
8
9
10
11
12
...
»

Содержание CNX-BIPAD8

































Отзывы:

Нет отзывов