background image

                                                                                                  CRESTRON                                                                                                  

Operations Guide - DOC. 8114

Contents  

••

  i

Contents

CNTS-N

1

Description.................................................................................................................................................1
Leading Specifications .............................................................................................................................2
Setup ...........................................................................................................................................................2

Identity Code .............................................................................................................................2
Preparation for Use ...................................................................................................................3
Programming ..............................................................................................................................3

Problem Solving.........................................................................................................................................7

Troubleshooting........................................................................................................................7
Further Inquiries........................................................................................................................7
Syntax..........................................................................................................................................7

Содержание CNTS-N













Отзывы: