manualshive.com logo in svg

Crest Audio X 18R, Руководство пользователя, Страница: 53 / 56

Поделиться
Скачать
Crest Audio X 18R Скачать руководство пользователя страница 53

Specifications

4

 

 

Specifications

 

Frequency Response

 

+0/-1 dB 20Hz-20kHz ref 1 kHz 

 

 

(any input to any  output)

 

THD

 

any output < 0.01% THD 20 Hz - 20kHz@ +15 dBu out

 

Noise

 

mic ein:  better than –128 dBu  20Hz to 20kHz  150 Ohm source, 60 dB gain

 

 

Bus Noise: better than -85 dBu

 

Crosstalk

 

channel mute  > 90 dB, channel routing  > 80 dB

 

 

channel fader attenuation > 90dB

 

 

aux send attenuation  > 85 dB

 

Phase Shift

 

< +/- 30 degrees, 20Hz to 20kHz – mic-in to main out

 

Mic-in

 

XLR 4k Ohm balanced 

 

 

max voltage gain to main outs = 100 dB

 

Line-in XLR and TRS

 

> 10k Ohms balanced

 

RCA Tape Input

 

> 10k Ohms unbalanced

 

Bus Inputs

 

> 10k Ohms balanced

 

L/R/M Outputs

 

XLR 100 Ohms balanced 

 

 

(switchable between line or mic level)

 

Group/Direct Out 

TRS 50 Ohms ground compensated

 

Aux Outputs

 

XLR & TRS 50 Ohms ground compensated

 

Headphones

 

Stereo, intended to drive > 8 Ohms

 

Dimensions

 

17.5" height (10u) x 19" width  x 4.5" depth behind panel

 

Weight

 

30 lbs.

 

Internal Power Supply 

100 - 240 VAC, 50/60Hz

 

Warranty

 

Five Years

Connector Pinout Detail

The rear panel of the X 18R/20R is screened with the pinout and electrical details of the I/O connectors. It is 
reprinted here for your reference.

X 18R/20R  Internal Options

The Input Channels have various options that can be selected. If specified at time of order, the factory will set-up 
the X-Series with the user’s desired settings. If configured from the factory, the appropriate check-box will be 
marked, showing which option was changed, and what it was changed to.

Aux PRE:

 This PRE source (within the channel) is normally Pre-fader. It can be changed to Pre-Insert or Pre-EQ 

and would apply to all PRE switches within that channel.

PRE-Follow Mute:

 Normally, the PRE signal (no matter what the source) will be muted when the main channel 

is muted (MUTE sw depressed). An option allows the PRE source to ignore the channel mute and be active 
(ON) at all times.

Channel Direct Out:

 This output is normally Post-fader. It can be changed to Pre-Fader on a channel-by-

channel basis.
 

p. 53

Содержание X 18R

























































Отзывы:

Нет отзывов