Crest Audio X 18R Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 56

Crest Audio X 18R Скачать руководство пользователя страница 43

Front Panel Features

MONITOR Output Section

SOURCE SELECT

The Source select portion of the Monitor system allows you to assign the primary mix
buses to the Monitor outputs.

NOTE:

All buses are monitored pre-fader (post-insert)

NOTE:

All selected sources are added (summed) together.

TAPE IN

Assigns the TAPE IN L & R signals to the monitors. The TAPE IN jacks are located
on the rear panel. 1/4” TRS jacks and RCA phone plugs are provided for easy
hookup.

A1-2 (Aux 1 & 2)

Assigns Auxes 1 and 2 to the Monitor outputs. Auxes 1 and 2 are configured
as a paired-stereo Aux bus (see Mono input channel description). Aux 1 is Left
and 2 is Right.

MONO

Assigns the Mono bus to both the Left and Right Monitor outs.

L-R (Left & Right)

Assigns the Left and Right buses to the Left and Right Monitor outs.

G1-2 (Groups 1 & 2)

Assigns Groups 1 and 2 to the Monitor outs. Group 1 is Left and 2 is Right.

G3-4 (Groups 2 & 4)

Assigns Groups 3 and 4 to the Monitor outs. Group 3 is Left and 4 is Right.

Master Section

3

p. 43

«
...
41
42
43
44
45
...
»

Содержание X 18R

























































Отзывы:

Нет отзывов