manualshive.com logo in svg

Crest Audio HP-EIGHT, Руководство пользователя

Поделиться
Скачать
Crest Audio HP-EIGHT Скачать руководство пользователя страница 55

p. 55

mono output

mono (main audio bus)

features

The HP-Eight is equipped with 3 main audio buses, in addition to the 8 audio sub-
groups.This section of the manual deals with 1 of those 3 main buses- the Mono bus.
The Mono bus is directly assignable from all of the Mono and Stereo Inputs, the 8
audio subgroups and the L-R main buses.

Since the Mono bus is directly-assignable from all input sources, and not a derived,
summed L-R mix, a variety of uses are possible: Center-cluster feed in a L-C-R church
install,subwoofer feed- assign only the appropriate,low-freq sources to the bus,or use
it to sum the L-R mixes to create a mono mix.

The Matrix Send

pots allow the user to mix the post-fader/pot-mute Mono signal

with other 2 main outputs, plus the 8 groups. If the PRE button is pressed, the signal
to the Matrix Send pots is pre-fader/pre-mute.This allows a totally independent out-
put mix to be created, the main fader level will not affect the Matrix mix.The overall
level of the entire Matrix mix is controlled by the Matrix Masters, located at the far
right of the Master section.

See Matrix section for further matrix information

Mute Switch w/LED

This switch will mute the post-fader output of the Mono audio bus.The LED

will illuminate when the mute is active.

100mm 

Fader

This high-quality, 100mm fader is used to control the main output level.Any
Post-fader feeds are affected by this control. Nominal position is at the “0”
mark, with 10dB additional gain available above that point.

PK/Sig LED

The FADER is equipped with a bicolor LED that displays the Pre-fader signal level
with varying intensity green illumination, and also indicates impending audio overload
(within 3dB of clipping) by turning red.Audio clipping is sensed both pre and post
fader, so even if the fader is down, you will be informed of any bus-related overload
problems.

AFL

An AFL (After-Fader Listen) switch is provided that lets the operator monitor the
audio signal in the Console’s Solo system.When depressed, the Mono’s post-fader,
post-mute signal sent to the Console’s Solo system (See Master section for details
on the Solo system functions).

write-in label

This filled-area may be written on with a grease-marker, and later wiped clean with a
cloth moistened with isopropyl or rubbing alcohol. Artist (Board) tape may also be
applied to this surface, and the tape marked with a Sharpie.

L E D

5

10

0

5

10

20

30

15

6

NOTE:

Do not write directly

on the Console’s surface with
a Sharpie or other permanent
marker. Use a china-marker
(grease pencil) or other
removable marking pencil, or
put down a strip of Artist tape
first.  Avoid using standard
masking tape; it dries out and
leaves a hard-to-remove glue
residue.

+

All Mono and Stereo
Inputs, along with the 8
groups and L-R, can be
directly assigned to the
Mono bus.

®

Use the Matrix Sends
to create additional mixes
from the 11 main buses (8
Groups, Left, Right &
Mono). These additional
mixes can be tailored to
suit a specific need, only
mix-in the signals you need,
or enhance the main-mix by
adding additional instru-
ments where needed.

®

Содержание HP-EIGHT





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды