background image

Copyright © 2013-2017 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree

®

 and XLamp

®

 are registered trademarks and the Cree logo is a trademark 

of Cree, Inc. Other trademarks, product and company names are the property of their respective owners and do not imply specific product and/or vendor endorsement, sponsorship or association. This 

document is provided for informational purposes only and is not a warranty or a specification. For product specifications, please see the data sheets available at www.cree.com.

8

XLamp

®

 mT FamiLy & mK FamiLy LED SoLDEring & HanDLing

XLaMp

®

 MT FaMILy anD MK FaMILy LED rEFLoW soLDErIng CHaraCTErIsTICs

In testing, Cree has found XLamp MT Family and MK Family LeDs to be compatible with JeDeC J-STD-020C, using the parameters listed 

below. As a general guideline, Cree recommends that users follow the recommended soldering profile provided by the manufacturer of the 

solder paste used, and therefore it is the lamp or luminaire manufacturer’s responsibility to determine applicable soldering requirements.

Note that this general guideline may not apply to all PCB designs and configurations of reflow soldering equipment.

profile Feature

Lead-Free solder

Average Ramp-Up Rate (Ts

max

 to Tp)

1.2 °C/second

Preheat: Temperature Min (Ts

min

120 °C

Preheat: Temperature Max (Ts

max

)

170 °C

Preheat: Time (ts

min

 to ts

max

)

65-150 seconds

Time Maintained Above: Temperature (T

L

)

217 °C

Time Maintained Above: Time (t

L

)

45-90 seconds

Peak/Classification Temperature (Tp)

235 - 245 °C

Time Within 5 °C of Actual Peak Temperature (tp)

20-40 seconds

Ramp-Down Rate

1 - 6 °C/second

Time 25 °C to Peak Temperature

4 minutes max.

Note: All temperatures refer to topside of the package, measured on the package body surface.

IPC/JeDeC J-STD-020C

T

P

T

L

Temper

atur

e

Time

t 25˚C to Peak

Preheat

ts

t

S

t

P

25

Ramp-down

Ramp-up

Critical Zone

T

L

 to T

P

Ts

max

Ts

min

Содержание XLamp MK Series













Отзывы: