manualshive.com logo in svg

Creator's Stained Glass Cutter's Mate, Руководство пользователя

Поделиться
Скачать
Creator's Stained Glass Cutter's Mate Скачать руководство пользователя страница 3

Cutter’s Mate 

Owner’s Manual 

3 van 14 

 

Cuttersmate-europe  2012 Rev. 1 

 

IMPORTANT! 

These instructions are presented for your safety !. 

Warning: 

Read all the following instructions and save them for future reference

. 

Cutter’s Mate is a device with moving parts and a cutting wheel. Without proper care  
and use, this device can cause personal injury. Please read and adhere to the  
following safety precautions. 

1.  Keep your work area clean and free of unnecessary clutter. Clutter can lead to injury. 

2.  Keep children away from the device and your  work area. 

3.  Avoid placing fingers or other appendages between moving parts. Care should be taken when 

assembling, disassembling, using, parking, and storing device. 

4.  Always wear safety glasses when using the device. Tiny pieces of glass will be produced when scoring 

and fracturing glass. 

5.  Maintain proper balance and control while using the device. 

6.  Properly care for and maintain your Cutter’s Mate tool for optimal performance  

and safety.  Follow instructions for lubrication of all moving parts and cutting wheel. Periodically inspect 
the cutting wheel and replace promptly when dull. 

7.  Any modification to or misuse of the device can be dangerous and may result in ineffective 

performance.

 

PLEASE READ AND SAVE THE PRECEDING INSTRUCTIONS  

Содержание Cutter's Mate















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды