Creative Sensor Technology DFM-6300 Series Скачать руководство пользователя | Manualshive

Страница: 6 / 30

background image

DFM-6300 Series

Instruction Manual

6

Connectors Labeling

The connectors’ label, affixed to the meter, shows the location of all connectors
available with requested configuration.

Warning!

Do not connect any equipment to the RJ45 M-LINK
connector. This connector is intended for factory use
only. If non-standard equipment is connected to the
M-LINK, damage will occur to the equipment and the
meter.

Figure 4: Connector Labeling for Fully Loaded PD6300-CS

Wiring Connections

Power connections are made to a two-terminal connector labeled POWER on Figure
4. The + and - symbols are only a suggested wiring convention.

Figure 5: Wiring Connections

«
...
4
5
6
7
8
...
»

Содержание DFM-6300 Series































Отзывы:

Нет отзывов

Похожие инструкции для DFM-6300 Series

Бренд: YOKOGAWA Страницы: 3

Бренд: Landis+Gyr Страницы: 54

Бренд: Yamaha Страницы: 120

Бренд: Yamaha Страницы: 110

Portatone PSR-5700

Бренд: Yamaha Страницы: 79

Бренд: Yamaha Страницы: 112

Бренд: Yamaha Страницы: 82

Бренд: Yamaha Страницы: 108

Бренд: YATO Страницы: 36

Cerabar S PMC71

Бренд: Endress+Hauser Страницы: 48

Бренд: Allen Organ Company Страницы: 29

Бренд: Biobase Страницы: 36

Бренд: Fluke Страницы: 5

Бренд: PCE Health and Fitness Страницы: 4

Бренд: Readiness Systems Страницы: 16

Бренд: xDEEP Страницы: 57

SUPER-CUTAWAY DIY ELECTRIC GUITAR KIT

Бренд: Gear4music Страницы: 24

Бренд: YZ Systems Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды