background image

© Copyright 2014, Creative Playthings

MODEL PS18EAS
19862-700 Rev A (07-20)

Page 2

PLAY SET SAFETY

Observing the following statements & warnings reduces the likelihood of serious or fatal injury:

•  Children should use equipment only in its intended manner.
•  Children should not wear loose or stringed clothing while using playground equipment.
•  Children should not play on equipment in wet weather conditions due to potentially slippery surfaces.
•  Children should NOT walk too closely in front of, behind, or between moving swings and trapezes.
•  Children should NOT swing empty swing seats.
•  Children should NOT jump off swings and/or trapeze while they are in motion.
•  Children should NOT twist swing chains because this will reduce the strength of the chains.
•  Children should sit in the center of the swings with their full weight on the seats.
•  Children should NOT be on the top surface of the swing beam.
•  Children should NOT use the equipment in a manner other than intended.
•  Children should NOT get off the equipment while it is in motion.
•  On-site adult supervision is required at all times for children of all ages.
•  Until assembly is complete, DO NOT let your children use the Play Set.
•  Never fasten anything not approved by Creative Playthings to your Play Set. Accessories or items not ap-

proved by Creative Playthings include; Dog runs, clothes lines, electrical devices, or bird feeders etc.

•  Suspended ropes, chains, and cables must be secured at both ends.
•  Suspended ropes, chains, and cables must not be capable of looping back on themselves.
•  Do not allow more than 120 lbs. on Single occupancy swing accessories such as the Sling Swing and Trapeze.
•  Do NOT allow more than 175 lbs. on multiple use swing accessories such as the Back-to-Back Plastic Glider.
•  Do NOT allow more children on the Play Set than can simultaneously use all the swing stations at one time.

•  Children MUST NEVER wear bicycle helmets while playing on the play-set.

Assembly Safety:

•  Adult assembly required
•  Face slide away from the sun.
•  Keep the work area clean and clear of obstructions.
•  Children should stay out of the work area until the safe play area is cleared of obstacles, the Play Set has been 

completely assembled, all hardware has been tightened and checked, and all tools have been picked up. 

•  Keep children off the Play Set until it has been completely assembled.
•  Parts of the assembly process may require help from another competent adult.
•  Do not stand on the platform until the Play Set has been completely assembled, use a step ladder if you can  

not reach high enough.

•  Follow the manufacturers' safety recommendations for the tools and equipment you use.
•  Avoid assembling your Play Set in poor weather conditions.
•  Wear proper clothing and safety equipment (safety glasses, boots, and gloves) while assembling your Play Set.

FOR SAFETY SAKE, PLEASE TAKE TIME TO READ ALL INSTRUCTIONS COMPLETELY AND 

CAUTION YOUR CHILDREN APPROPRIATELY.

Содержание Playtime PS18EAS





















Отзывы: