Creative Playthings Pine Skybox Spiral Slide SH902-810 Скачать руководство пользователя страница 5

Страница: 5 / 8

PINE SKYBOx SPIRAL SLIDE

19694-200 Rev C (07-16)

Page 5

ASSembly inStruCtionS

SteP 5 - entrance Assembly to Gym

Install the Entrance Assembly to the Gym through the two

holes in the Wall Support. Attach using two 5/16 x 3" Hex

Bolt Assemblies as shown.
Note: This step will require two people.
Fasten the bottom of the Entrance Assembly to the Gym

through the two holes in the Platform Support. Attach using

two 5/16 x 1-1/2" Hex Bolt Assemblies as shown.
Attach the Entrance Assembly through the top and bottom

two holes using four 5/16 x 1-1/2" lag screws and four 5/16"

flat washers.
Attach the side center three holes on both sides using six

5/16 x 2-1/2" lag screws and six 5/16" flat washers.

important: in any place where hardware penetrates a

piece of wood, use the gray "xylan coated" hardware,

which has grater resistance to corrosion.

SteP 5 - Slide entrance Assembly

Assemble the Left Entrance Section to the Right Entrance

Section using fourteen 5/16 x 3/4" hex bolts, twenty-eight

5/16" flat washers and fourteen 5/16" Nylok nuts.
Attach the Entrance assembly to the Mounting Plate at

the four corners using four 5/16 x 1" hex bolts, eight 5/16"

flat washers and four 5/16" Nylok nuts as shown in the

illustration on the right. Make sure that the Nylok nuts are

installed to the outside away from the Gym.
NOTE: The Mounting Plate is stamped “TOP". Make sure

that it is positioned properly and that all of the holes around

the Mounting Plate line up before tightening.

Lag Screws

5/16 x 1-1/2"

Lag Screws

5/16 x 2-1/2"

Hex Bolt

5/16 x 3"

Wall Support

Hex Bolts

5/16 x 1"

Mounting

Plate

SteP 7 - Assemble elbow Sections

Locate all of the Elbow Sections.
NOTE: The difference between the top and bottom sections

is the male and female flanges.
Assemble each of the two Elbow assemblies using thirteen

5/16 x 3/4" hex bolts, twenty-six 5/16" flat washers and

thirteen 5/16" Nylok nuts as shown in the illustration.
Assemble the remaining Elbow Section, Outlet Section and

the Lower Slide Bracket using thirteen 5/16 x 3/4" hex bolts,

twenty-six 5/16" flat washers and thirteen 5/16" Nylok nuts.

Platform

Support

Hex Bolt

5/16 x 1-1/2"

Содержание Pine Skybox Spiral Slide SH902-810









Результаты поиска

Содержание Pine Skybox Spiral Slide SH902-810

Отзывы:

Похожие инструкции для Pine Skybox Spiral Slide SH902-810

Бренды по названию

Популярные бренды

Creative Playthings Pine Skybox Spiral Slide SH902-810, Инструкция по сборке

Результаты поиска

Содержание Pine Skybox Spiral Slide SH902-810

Отзывы:

Похожие инструкции для Pine Skybox Spiral Slide SH902-810

Бренды по названию

Популярные бренды