Creative Playthings FUNTIME swing sets Скачать руководство пользователя страница 15

Страница: 15 / 36

MODEL MQHAR

19856-100 Rev D (05-14)

Page 15

AssEMbLy InsTRuCTIOns

sTEP 13 – Right Wall & Roof supports:

As with the previous step. Check the top holes in the Mid-

post (D).
Secure the Right Wall Support (BH) to the front right post,

then the Midpost and Roof upright (N) as in the previous

step. Fasten the Roof Ladder Rail (BQ), now part of the up-

per ladder assembly, to the back right post and Right Wall

Support using one 1/4 x 3-1/2" Hex Bolt Assembly through

the top hole in the Wall Support.
Fasten the Center Ladder Rail to the Platform Back using a

1/4 x 3" Hex Bolt Assembly.

sTEP 14 – End support:

Fasten the End Support (BZ) to the front left and right

post assemblies as shown at right. use 1/4 x 4" Hex Bolt

Assemblies in the top holes and 1/4" x 2" Lag Screws with

1/4" Flat Washers in the bottom holes.

sTEP 15 – Lookout Posts and Platform sides:

1) Fasten the back posts, assembled in step 3, to the Look-

out Base Sides (CG), using 1/4 x 3" Hex Bolt Assemblies

through the top holes. use 1/4 x 2" Lag Screws with Flat

Washers in the lower holes.
2) Orient the Lookout Platform Sides (BO) with counter-

bored holes facing outward as shown at right. Fasten the

Lookout Platform Sides to the back posts using 5/16 x 4"

Hex Bolt Assembly through the larger holes in the posts.
3) Fasten the other end of the Lookout Platform Sides to

the back of the gym assembly using 1/4 x 5" Hex Bolt As-

semblies. The bolt goes through the bottom hole in the wall

support, the gym post, the roof support and then through the

bottom hole in the Lookout Platform Side. use a 1/4" x 2-1/2"

Lag Screw and Flat Washer through the top hole in each

Lookout Platform Side to finish securing the part to the gym.

1/4 x 5" Hex Bolt

bottom holes

5/16 x 4"

Hex Bolt

1/4 x 3"

Hex Bolt,

top

1/4 x 2-1/2" Lag

Screw top holes

1/4 x 2" Lag

Screw bottom

(Only 5/16"

fastener on

tower portion

of swing set.)

3-1/2" Hex

Bolts

Top Hole

Only

2" Hex

Bolt

3" Hex

Bolt

2" Lag

Screw

2" Lag Screw in

bottom holes

4" Hex Bolt

Assembly in top

holes

Содержание FUNTIME swing sets





































Результаты поиска

Содержание FUNTIME swing sets

Отзывы:

Похожие инструкции для FUNTIME swing sets

Бренды по названию

Популярные бренды

Creative Playthings FUNTIME swing sets, Инструкция по сборке

Результаты поиска

Содержание FUNTIME swing sets

Отзывы:

Похожие инструкции для FUNTIME swing sets

Бренды по названию

Популярные бренды