manualshive.com logo in svg

CREATIVE ELECTRONICS SMC-3303X, Руководство по эксплуатации

Поделиться
Скачать
CREATIVE ELECTRONICS SMC-3303X Скачать руководство пользователя страница 19

- 16 - 

5. REMOTE CONTROL   

 

5.1 Remote Control Setup 

Background 

The power supply is capable of being remotely controlled via the USB connection. 

 

 

Interface 

  USB slave port, rear panel 

 

 

COM setting 

Set up the COM port inside the PC according to the following list: 

Baud rate: 9600 

Parity bit: None 

Data bit: 8 

Stop bit: 1 

Data flow control: None 

 

 

Functionality check 

Run this query command via the terminal application such as MTTTY (Multi-threaded 

TTY). 

*IDN? 

This should return the identification information: series number, firmware version. 

 

 

 

 

5.2 Remote Connection Step 

Enter the remote control 

mode 

1.

 

Connect the USB cable to the slave port. 

2.

 

The connection will be automatically established, and the front panel shows 

“USB…YES” message. 

 

3.

 

The power supply also automatically enters the lock state (the Lock key will be 

activated). 

 

 

 

Exit the remote control 

mode 

1.

 

Disconnect the USB cable from the rear. 

2.

 

The display shows “USB…NO” message. 

 

 

3.

 

Unlock the power supply by pressing the Lock key until it turns off backlight. 

 

4.

 

The power supply goes back to local operation mode. 

 

 

Содержание SMC-3303X

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды