Crane WEINMAN WE411 страница 17 Скачать руководство пользователя | Manualshive

Страница: 17 / 22

background image

IMPORTANT !

WARRANTY REGISTRATION

Your product is covered by the enclosed Warranty.

Complete the Warranty Registration Form and returned to

Crane Pumps & Systems, Inc. Warranty Service Group

IMPORTANT! If you have a claim under the provision of the warranty,

contact your local Crane Pumps & Systems, Inc. Distributor.

RETURNED GOODS

RETURN OF MERCHANDISE REQUIRES A "RETURNED GOODS AUTHORIZATION".

CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR.

   Products Returned Must Be Cleaned, Sanitized,
   Or Decontaminated As Necessary Prior To Shipment,
   To Insure That Employees Will Not Be Exposed To Health
   Hazards In Handling Said Material. All Applicable Laws
   And Regulations Shall Apply.

17

«
...
15
16
17
18
19
...
»

Содержание WEINMAN WE411























Отзывы:

Нет отзывов

Похожие инструкции для WEINMAN WE411

Бренд: Eagle Страницы: 16

Бренд: Jackco Страницы: 8

Sewers 1000 Series

Бренд: E-one Страницы: 3

Бренд: E-one Страницы: 23

Бренд: E-one Страницы: 76

Бренд: Zoeller Страницы: 12

Бренд: Gardena Страницы: 16

Бренд: Gardena Страницы: 9

Бренд: Gardena Страницы: 11

13000 aquasensor

Бренд: Gardena Страницы: 14

Бренд: Chiltrix Страницы: 54

Бренд: York Страницы: 24

Бренд: ELCOS Страницы: 8

Бренд: Takagi Страницы: 56

Бренд: Lincoln Страницы: 16

Бренд: Oprema Страницы: 8

Бренд: Pro-Source Страницы: 24

Бренд: Carlisle Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды