Crane WEINMAN WE411 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 22

Crane WEINMAN WE411 Скачать руководство пользователя страница 11

Insert so that the finished surface is up and the grooved surface
is against the seal plate. Make sure the stationary member is
in straight and that the rubber ring is not out of it’s groove.

DO NOT HAMMER ON THE SEAL PUSHER - IT WILL
DAMAGE THE SEAL FACE.

Place spring retainer and spring

onto motor shaft. Lightly oil shaft (

DO NOT use grease

) and

inner surface of bellows of rotating member. With finished end
away from motor, slide rotating member over bullet and onto
shaft until it engages spring (see Fig. 7b). Carefully assemble
shaft to seal plate as per section F-3.3. It is extremely important
to keep seal faces clean during assembly. Dirt particles lodged
between these faces will cause the seal to leak. When seal
plate is assembled to motor, it will properly align and seat the
seal (3) and bearing (4). Follow complete reassembly
instructions as per section F-3.3.

F-4.3) Replacing Exclusion Seal:

The exclusion seal (14), helps to keep debris away from the
shaft seal where it could cause damage. The exclusion seal
should be replaced whenever the shaft seal is replaced. To
replace the exclusion seal, pull the old seal off the shaft, and
slide the new seal on with the thin lip towards the motor. Be
sure not to damage the lip of the seal. Finger pressure is all that
is needed to install the exclusion seal.

MOTOR, SLEEVE &

BEARING

RETAINING

RING (3a)

SPRING (3b)

BULLET

ROTATING

MEMBER (3c)

SEAL PUSHER

Fig. 7b

SECTION: G REPLACEMENT PARTS

G-1 ORDERING REPLACEMENT PARTS:

When ordering replacement parts,

ALWAYS

furnish the

following information:

1. Pump serial number and date code. (Paragraph G-4)
2. Pump model number. (Paragraph G-3)
3. Pump part number. (Paragraph G-2)
4. Part description.
5. Item part number.
6. Quantity required.
7. Shipping instructions.
8. Billing Instructions.

G-2 PART NUMBER:

The part number consists of a six (6) digit number, which
appears in the catalog. A one or two letter suffix may follow
this number to designate the design configuration. This
number is used for ordering and obtaining information.

G-3 MODEL NUMBER:

This designation consists of numbers and letters which
represent the discharge size, series, horsepower, motor
phase and voltage, speed and pump design. This number is
used for ordering and obtaining information.

G-4 SERIAL NUMBER:

The serial number block will consist of a six digit number,
which is specific to each pump and may be preceded by a
alpha character, which indicates the plant location. This
number will also be suffixed with a four digit number, which
indicates the date the unit was built (Date Code).

EXAMPLE:

A012345 0490.

Reference the six digit portion (Serial Number) of this
number when referring to the product.

1

3

2

11

«
...
9
10
11
12
13
...
»

Содержание WEINMAN WE411























Отзывы:

Нет отзывов