background image

3

USER GUIDE

Congratulations on your purchase of a Barnes 

Ultra

GRIND™ grinder pump system. With 

proper care and by following a few simple 
guidelines your grinder pump will give you 
many years of dependable service.

Use and Care

The 

Ultra

GRIND grinder pump station is 

designed to handle routine, domestic sewage. 
Solid waste materials should be thrown in 
the trash. While your station is capable of 
accepting and pumping a wide range of 
materials, regulatory agencies advise that the 
following items should not be introduced into 
any sewer either directly or through a kitchen 
waste disposal:

• Glass
• Metal
• Diapers
• Socks, rags or cloth
• Plastic objects (e.g., toys, utensils, etc.)
• Sanitary napkins or tampons

In addition you must 

NEVER

 introduce into any 

sewer:

• Explosives
• Flammable Material
• Lubricating Oil and/or Grease
• Strong Chemicals
• Gasoline

General Information

Your home wastewater disposal service is part of 
a low pressure sewer system. The key element 
in this system is the Barnes 

Ultra

GRIND grinder 

pump station. The basin collects all wastewater 
from the house. The solids in the sewage are 
then ground to a small size suitable for pumping 
in the slurry.

The grinder pump  generates suffi cient
pressure to pump this slurry from your home to
the wastewater plant.

Power Failure

Your grinder pump cannot dispose of 
wastewater or provide an alarm signal without 
electrical power. If electrical power service is 
interrupted, keep water usage to a minimum.

Warranty

Your grinder pump is furnished with a 
warranty against defects in material or 
workmanship. A properly completed 
Start-Up/Warranty Registration form must 
be on fi le at the Barnes factory in order to 
activate your warranty. In addition your pump 
must be installed in accordance with the 
installation instructions.
If you have a claim under the provisions of the 
warranty, contact your local Barnes Pumps, 
Inc. Distributor.
When contacting your representative for 
service, please include your station serial 
number, pump model number, and pump 
serial number.

For future reference, record the following 
information:
Station Serial No:

Pump Model No:

Pump Serial No:

Local Distributor:

Distributor Telephone:

USER GUIDE

Содержание Barnes SGVF Series





















Отзывы: