Crane 4SHD страница 27 Скачать руководство пользователя

Страница: 27 / 38

Seal Kit includes:

• Lower Volute O-Ring (option 1)

• Lower Volute O-Ring (option 2)

• Lower Volute O-Ring (option 3)

• Seal Plate Upper O-ring

• Upper and Lower Stator O-Rings

• Terminal Block O-ring

• Retaining Rings

• Key

• Upper Mechanical Seal

• Lower Mechanical Seal

• Cord attachment O-ring

• Seal Pins

NOTE:

Kit contains hardware your pump may not require.

Seal Kits

Seal Kit

Part No.

I.B. Seal

Part No.

I.B. Seal

Material

O.B. Seal

Part No.

O.B Seal

Material

140613

138315

Carbon / Ceramic

138315

Carbon / Ceramic

140614

(STD)

138315

Carbon / Ceramic

138315SD

Silicon Carbide / Silicon Carbide

140615

138315

Carbon / Ceramic

138315SB

Tungsten Carbide / Tungsten Carbide

140616

138315SD

Silicon Carbide / Silicon Carbide

138315SD

Silicon Carbide / Silicon Carbide

140617

138315SD

Silicon Carbide / Silicon Carbide

138315SB

Tungsten Carbide / Tungsten Carbide

140618

138315SB

Tungsten Carbide / Tungsten Carbide

138315SB

Tungsten Carbide / Tungsten Carbide

Bearing Kit includes:

• Upper Ball Bearing

• Lower Ball Bearing

• Wavy Spring Washer

• Retaining Rings

Volute Kit includes:

• Wear Ring (if required)(pressed)

• Volute (painted)

Seal Plate Kit includes:

• Spring Pin

• Pipe Plug

• Seal Plate (painted)

Hardware Kit includes:

• Socket Head Cap Screws (for Motor Cap)

• Impeller Bolt and Washer Set

• Socket Head Cap Screws

(for Upper Seal Plate and Bearing Bracket)

• Socket Head Cap Screws (for Motor Leads)

• Socket Head Cap Screws (Ground Screw)

• Socket Head Cap Screws (for Handle)

• Socket Head Cap Screws (for Volute)

• Cord Attachment Screws

• Spring Pin

• Pipe Plug

NOTE:

Kits contain hardware your pump may not require.

Moisture Sensor Kit includes:

• 18” Orange Wire Jumper

• 24” Blue Wire Jumper

• Moisture Sensor Resistor

• Moisture Sensor

• 36” Orange Wire Jumper

• Wire Connector Clip

• 24” Orange Wire Jumper

Impeller Attachment Kit includes:

• Impeller Washer

• Impeller Bolt

Bearing Bracket Kit includes:

• Bearing Bracket (painted)

• Large Pipe Plug

• Spring Pin

Terminal Block includes:

• Terminal Block

• Terminal Block O-ring

• Terminal Block Alignment Pin

• Terminal Block Retaining Ring

• Motor Lead Screws

Motor Cap Kit includes:

• Upper Motor Housing Cap

• Pipe Plug

• Ground Screw

• Caution Tag

• Dowel Pin

Содержание 4SHD







































Результаты поиска

Содержание 4SHD

Отзывы:

Похожие инструкции для 4SHD

Бренды по названию

Популярные бренды

Crane 4SHD, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 4SHD

Отзывы:

Похожие инструкции для 4SHD

Бренды по названию

Популярные бренды