CRANE PUMPS & SYSTEMS 6SED-L Series Скачать руководство пользователя страница 2

Страница: 2 / 20

TABLE OF CONTENTS

SAFETY FIRST ............................................................................................... 3

PUMP

SPECIFICATIONS

................................................................................4

GENERAL

INFORMATION

..............................................................................5

INSTALLATION ................................................................................................5 - 6

ELECTRICAL

DATA

.........................................................................................6

START-UP

OPERATION

..................................................................................6

PREVENTATIVE

MAINTENANCE

...................................................................7

SERVICE and REPAIR ....................................................................................7 - 11

REPLACEMENT

PARTS

..................................................................................11

TROUBLE

SHOOTING

....................................................................................12

CROSS-SECTION (Fig. 9) ..............................................................................13

EXPLODED VIEW, (Fig. 10) ...........................................................................14

PARTS LIST ...................................................................................................15 - 16

RETURNED GOODS POLICY .........................................................................19

WARRANTY

...................................................................................................20

START-UP REPORT ........................................................................................21 - 22

WARRANTY

REGISTRATION

SPECIAL

TOOLS

AND

EQUIPMENT

INSULATION

TESTER

(MEGGER)

DIELECTRIC

TESTER

SEAL TOOL KIT ( see parts list)

PRESSURE GAUGE KIT (see parts list)

Other brand and product names are trademarks or registered trademarks of their respective holders.
® PROSSER is a registered trademark of Crane Pumps & Systems, Inc

1996,

2002,

5/06,

9/06

Alteration

Rights

Reserved

Содержание 6SED-L Series





















Результаты поиска

Содержание 6SED-L Series

Отзывы:

Похожие инструкции для 6SED-L Series

Бренды по названию

Популярные бренды

CRANE PUMPS & SYSTEMS 6SED-L Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 6SED-L Series

Отзывы:

Похожие инструкции для 6SED-L Series

Бренды по названию

Популярные бренды