Craftsman CMCVS001B0G0HP, Инструкция по эксплуатации

Страница: 12 / 36

English
10
Versatrack™ (Fig. I, J, Q)
WARNING:
To reduce the risk of serious
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
WARNING:
To reduce the risk of serious
personal injury, do not use a damaged Versatrack™
integral hang hook or Versatrack™ Trackwall.
A damaged Versatrack™ integral hang hook or
Versatrack™ Trackwall will not support the weight of
the tool.
WARNING:
To reduce the risk of serious
personal injury, DO NOT suspend tool overhead or
suspend objects from the integral hang hook. ONLY
suspend tool on the Versatrack™ Trackwall using the
integral hang hook.
WARNING:
The Versatrack™ integral hang
hook is intended to mount the tool onto a Versatrack™
Trackwall rail. Do not use the integral hang hook to
mount the tool to any other surface.
WARNING:
The Versatrack™ integral hang
hook is not a belt hook.
WARNING:
When hanging objects on a
Versatrack™ Trackwall rail, adequately space the tools
in order to not exceed 75 lb (35 kg) per linear foot.
Accessories
WARNING:
Since accessories, other than
those offered by CRAFTSMAN, have not been tested
with this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be used
with this product.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service
center. If you need assistance in locating any accessory, please
contact CRAFTSMAN call
1-888-331-4569
.
Replacing the Filters
The filters should be replaced every 6 to 9 months and
whenever worn or damaged. Replacement filters are
available from your CRAFTSMAN dealer.
Visit
www.craftsman.com to locate dealers.
• Remove the old filters as described in
Cleaning the Filters
.
• Fit the new filters as described in Cleaning the Filters .
(cat. no: CMCVSF1)
• Empty the dust canister into a trash bin.
• Install the pre-filter
19 into the dust canister 9 ensuring
the dust canister tab 20 aligns with the pre-filter slot 21
as shown in Fig. N.
• Install the dust canister onto the vacuum, until it clicks
firmly into position.
iMPORTAnT: Maximum dust collection will only be
obtained with clean filters and an empty dust canister.
If dust begins to fall back out of the product after it is
switched off, this indicates that the dust canister is full and
requires emptying.
Removing Filter (Fig. l, M, O)
• Lift and remove the lift away dust canister 9 from the
chassis 16 as shown in Figure L.
• Place the dust canister over a trash bin and press the dust
canister lid release button 17 to empty the dust canister
as shown in Figure M.
• Grasp the agitator wheel housing 22 and pull up
to remove.
• Remove the filter 23 , from the agitator wheel
housing
22
as shown in Fig. O.
• Shake off or lightly brush any loose dust from the filter.
• Install the the filter
23 , into the agitator wheel
housing 22 .
• Install the agitator wheel housing 22 onto the dust
canister, until it clicks firmly into position.
Cleaning the Filters (Fig. n, O)
• Once the filter and pre-filter are removed from the dust
canister shake off or lightly brush any loose dust from the
pre-filter
19 and filter 23 .
• Rinse out the dust canister 9 with warm soapy water.
• Wash the filters with warm soapy water.
• Ensure the filters are completely dry before refitting.
• Follow instructions in the
Removing pre-filter and
Removing filter sections for assembly instructions.
•
iMPORTAnT:
Maximum dust collection will only be
obtained with clean filters and an empty dust canister.
If dust begins to fall back out of the product after it is
switched off, this indicates that the dust canister is full
and requires emptying.
• Wash the filters regularly using warm, soapy water and
ensure that it is completely dry before using again. The
cleaner the filter is, the better the product will perform.
• It is very important that the filters are completely dry and
correctly in position before use.
Removing and Cleaning the Rotary Brushes (Fig. P)
CAUTION:
To reduce the risk of injury from
moving parts, disconnect lift away canister before
cleaning or servicing.
• To remove the rotary brush 24 from the floor brush 10
Depress the release button 25 as shown in Figure P.
• The rotary brush 24 can now be removed.
• Clean rotary brush, and reinstall. Ensure it is secured in its
locked position before operating.