Craftsman CMCMWSP220, Инструкция по эксплуатации

Страница: 12 / 44

English
10
Adjusting Mower Height (Fig. H)
The height of cut is adjusted by the cut height adjust
lever
10 .
Mulching (Fig. G)
DANGER: Turn unit off and remove safety key and
battery packs.
1. To operate mower in mulching mode, remove the grass
collection bag 12 .
2. Be sure rear door cover 11 is closed.
Grass Collection Bag (Fig. G)
DANGER:
Turn unit off and remove safety key and
battery packs.
1. To attach, lift the rear door cover 11 and place the grass
collection bag 12 onto the mower so the bag hooks on
frame 16 slide into the bag pins on mower 17 . Then,
lower the rear door cover onto the bag.
2. To remove, lift the rear door cover and pull the grass
collection bag off of the mower by unhooking it off the
bag pins. Then, lower the rear door cover so it fully covers
the back opening.
Adjusting Handle Height (Fig. F)
The mower is shipped in storage mode. You will need to
adjust the handle to operating position before continuing.
1. To unlock the handle 4 from the storage position, twist
the two handle lock knobs 6 a quarter turn. The handle
lock knobs are located on both sides of the handle.
2. Raise the handle to the operating position. Take care to
not pinch or stress the cord.
3. Twist the handle lock knobs a quarter turn, securing the
handle into position.
Assembling the Grass Collection Bag (Fig. E)
WARNING:
Under normal usage, the collection
bag assembly is subject to deterioration and
wear and should, therefore, be frequently
checked for replacement. Any replacement
assembly should be checked for compliance with
CRAFTSMAN recommendations.
1. Before starting to assemble the grass collection bag 12
to the frame 16 , check that the grass bag and frame are
similar to Fig. E.
2. Slide the frame into the bag, ensuring the bag handle 13
remains outside the bag.
3. Assemble the top clips to the frame, then assemble the
two side clips and the bottom clip last.
ASSEMBLY AND ADJUSTMENTS
DANGER: To reduce the risk of serious personal
injury, turn unit off and remove the safety key and
battery packs before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Wall Mounting
Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1” (25.4 mm) long, with a screw head
diameter of 0.28–0.35” (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32” (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
nOTE: Do not attempt to mount CMCB101 charger under a
bench or table.
nOTE: Only mount CMCB101 charger with the charging
lights pointed upward toward the ceiling.
VersaTrack™
WARNING: Do not charge batteries while charger is
hung on Trackwall.
CRAFTSMAN chargers, except the CMCB101, can be
stored on CRAFTSMAN VersaTrack™ Trackwall. Hooks and
accessories are sold separately. Please refer to the VersaTrack™
Trackwall accessory sheet for further information.
nOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™
Trackwall compatible.
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65 °F – 75 °F (18 °C – 24 °C);
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse effect on the battery pack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles should
be kept away from charger cavities. Always unplug the
charger from the power supply when there is no battery
pack in the cavity. Unplug the charger before attempting
to clean.
6. Do not freeze or immerse the charger in water or any
other liquid.
Charger Cleaning Instructions
WARNING:
Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.