Craftsman 917.27636 Скачать руководство пользователя | Manualshive

Страница: 32 / 34

background image

32

PROBLEM CAUSE CORRECTION

Mower blades will

1. Obstruction in clutch 1. Remove obstruction.

not rotate

mechanism.

2. Worn/damaged mower 2. Replace mower drive belt.

   drive belt.
3.   Frozen idler pulley.     3.   Replace idler pulley.
4.   Frozen blade mandrel.     4.   Contact a Sears or other
   qualifi ed service center.

Poor grass

1. Engine speed too slow. 1. Place throttle control in

discharge

“FAST” position.

2.   Travel speed too fast.     2.   Shift to slower speed.
3.   Wet grass.   3.   Allow grass to dry before
   mowing.
4.   Mower deck not level.   4.   Level mower deck.
5.   Low/uneven tire air pressure.  5.   Check tires for proper air
   pressure.
6.   Worn, bent or loose blade.   6.   Replace/sharpen blade.
   Tighten blade bolt.
7.   Buildup of grass, leaves and    7.   Clean underside of mower
   trash under mower.      housing.
8.   Mower drive belt worn.   8.   Replace mower drive belt.
9.   Blades improperly installed.   9.   Reinstall blades sharp edge
   down.
10. Improper blades used.     10. Replace with blades listed
   in this manual.
11. Clogged mower deck vent   11. Clean around man drels to
   holes from buildup of   open vent holes.
   grass, leaves, and trash
   around mandrels.

Headlight(s) not

1. Light switch is “OFF”. 1. Turn light switch “ON”.

working

2. Bulb(s) or lamp(s) burned out. 2. Replace bulb(s) or lamp(s).

(if so equipped)

3. Faulty light switch. 3. Check/replace light switch.

4.   Loose or damaged wiring. 4.   Check wiring and connec-
   tions.
5.   Blown fuse.   5.   Replace fuse.

Battery will not

1. Bad battery cell(s). 1. Replace battery.

charge

2. Poor cable connections. 2. Check/clean all connec-

tions.
3. Faulty regulator 3. Replace regulator.

(if so equipped).
4. Faulty alternator. 4. Replace alternator.

Loss of drive

1. Freewheel control in 1. Place freewheel control in

   “disengaged” position.    “engaged” position.
2.   Motion drive belt worn,   2.   Re place motion drive belt.
   damaged, or broken.
3.   Air trapped in transmission      3.   Purge transmission.
   during shipment or servicing.

Engine “backfi res”

1. Engine throttle control not set 1. Move throttle control

when turning

between half and full speed between half and full speed

engine “OFF”

(fast) position before stopping (fast) position before

engine. stopping engine.

TROUBLESHOOTING CHART:
See ap pro pri ate section in manual un less di rect ed to Sears service center

«
...
30
31
32
33
34
»

Содержание 917.27636



































Отзывы:

Нет отзывов

Похожие инструкции для 917.27636

Бренд: H&S Страницы: 32

Бренд: Cobra Страницы: 19

Бренд: SIP Страницы: 189

Бренд: Yard-Man Страницы: 42

Бренд: Simplicity Страницы: 14

Бренд: Parkside Страницы: 124

Бренд: MTD Страницы: 35

Бренд: Toro Страницы: 24

Бренд: Weed Eater Страницы: 30

Бренд: FLORABEST Страницы: 92

Бренд: Craftsman Страницы: 18

Бренд: Craftsman Страницы: 18

Бренд: Craftsman Страницы: 30

Бренд: Craftsman Страницы: 30

Бренд: Craftsman Страницы: 30

Бренд: Craftsman Страницы: 30

Бренд: Craftsman Страницы: 31

Бренд: Craftsman Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды