manualshive.com logo in svg

Craftsman 917.27636, Руководство пользователя

Поделиться
Скачать
Craftsman 917.27636 Скачать руководство пользователя страница 31

31

 PROBLEM                CAUSE                                        CORRECTION 

Loss of power         

1.   Cutting too much grass/too      1.   Raise cutting height/reduce 

                                       fast.                                                speed.
                                 2.   Throttle in “CHOKE”                 2.   Adjust throttle control.   
                                       position.
                                 3.   Build-up of grass, leaves         3.   Clean underside of mower  
                                       and trash under mower.                 housing.
                                 4.   Dirty air fi lter.                           4.   Clean/replace air fi lter.
                                 5.   Low oil level/dirty oil.                5.   Check oil level/change oil.
                                 6.   Faulty spark plug.                    6.   Clean and regap or change  
                                                                                             spark plug.
                                 7.   Dirty fuel fi lter.                          7.   Replace fuel fi lter.
                                 8.   Stale or dirty fuel.                    8.   Empty fuel tank and refi ll tank  
                                                                                                  with fresh, clean gas o line.
                                 9.   Water in fuel.                           9.   Empty fuel tank and    
                                                                                             carburetor, refi ll tank with  
                                                                                             fresh gasoline and replace  
                                                                                             fuel fi lter.
                                 10. Spark plug wire loose.             10. Connect and tighten spark  
                                                                                             plug wire.
                                 11. Dirty engine air screen/fi ns.     11. Clean engine air screen/fi ns.
                                 12. Dirty/clogged muffl er.               12. Clean/replace muffl er.
                                 13. Loose or damaged wiring.       13. Check all wiring.
                                 14. Carburetor out of                     14. See “To Adjust Carburetor”  
                                       adjustment.                                    in Service and Adjustments  
                                                                                             section.
                                 15. Engine valves out of                15. Contact a Sears or other  
                                       adjustment.                                    qualifi ed service center.

Excessive 

              1.   Worn, bent or loose blade.      1.   Replace blade. 

 

vibration                                                                             

Tighten blade bolt.

                                 2.   Bent blade mandrel.                2.   Contact a Sears or other
                                                                                             qualifi ed service center. 
                                 3.   Loose/damaged part(s).          3.   Tighten loose part(s).   
                                                                                             Re place damaged parts.

Engine dies when 

 1.   Reverse operation system       1.   Turn ignition key to

tractor is shifted 

         (ROS) is not "ON" while                 ROS "ON" position.

into reverse

                  mower or other attachment            See Operation section.

                                       is engaged.

Engine continues   

1.   Faulty operator-safety              1.   Check wiring, switches and  

to run when

                  presence control system.               connections. If not cor rect ed,

operator leaves       

                                                           contact a Sears or other  

seat with                  

                                                           qualifi ed service center.

attachment                                                                         
clutch engaged

Poor cut - uneven   

1.   Worn, bent or loose blade.      1.   Replace blade.  Tighten  

                                                                                             blade bolt.
                                 2.   Mower deck not level.              2.   Level mower deck.
                                 3.   Buildup of grass, leaves,          3.   Clean underside of mower  
                                       and trash under mower.                 housing.
                                 4.   Bent blade mandrel.                4.   Contact a Sears or other
                                                                                             qualifi ed service center.
                                 5.   Clogged mower deck vent       5.   Clean around man drels to 
                                       from build-up of grass,                   open vent holes. 

 

                                       leaves, and trash around         
                                       mandrels.

TROUBLESHOOTING CHART: 
See ap pro pri ate section in manual un less di rect ed to Sears service center

Содержание 917.27636



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды