background image

I

7

Items Needed:

Bottle Opener (Qty:1)

M4x12 Screw (Qty: 2)

• Align the holes in Bottle Opener with Bottle Opener 

  attachment holes on left side of Crossbar.

• Tighten (2) M6x12 screws through Bottle Opener holes 

  into Crossbar holes as shown in figure below. 

 

 

Note: The Left Leg Panel has pegboard holes through  

which hooks can be attached for hanging hand tools, work  

lights and similar items. 

E

G F

 

Items Needed:

Power Strip

M6x12 Screw (Qty: 6)

Power Strip Cover

• Insert the Power Strip (F) into the Power Strip Cover (G).

• Align the Power Strip Cover holes with the perimeter 

  holes of the opening for the Power Strip on the inside 

  of the Right Leg Panel. 

• Tighten (6) M6x12 screws through Power Strip Cover 

  holes into Leg Panel holes as shown in the figure below. 

Note: 

• The power strip has receptacle holes for four 3-pronged 

  plugs. It also has two USB ports for charging electronic 

  devices. 

• Once power strip is plugged in, push toggle switch to 

  RESET position for power strip operation.

E

 

Items Needed:

Back Rail

M6x12 Screw (Qty: 8)

IMPORTANT: Before attaching Back Rail, adjust height of 

Leg Panels to the planned Workbench location. See 

Workbench Height Adjustment section on next page. 

Attach Back Rail (E) to back of Left and Right Leg Panels: 

• Align Back Rail end holes with holes in back of Left and 

  Right Legs.

• Tighten (4) M6x12 screws through Back Rail end holes 

  into Leg holes as shown in figure below. 

Note: The Back Rail end flanges must be attached so that 

they are on the outside of the Leg Panels. 

• Once the Back Rail is attached, go back and fully tighten 

  all screws that were partially tightened up to this point in 

  the assembly process. 

4

H

6

Items Needed:

Cord Holder

M6x12 Screw (Qty: 2) 

 

 

• With the aid of an assistant, set the the workbench in 

  upright position.

• Align the holes in Cord Holder with Cord Holder  

  attachment holes on outside of Right Leg Panel. 

• Tighten (2) M6x12 screws through Cord Holder holes  

   into Right Leg Panel holes as shown in figure below. 

Содержание 76633 Butcher Block







Отзывы: