background image

A. Workbench Wood Table

B. Crossbar

A

B

B

G F

E

C

I

D

H

C. Left Leg Panel

D. Right Leg Panel

E. Back Rail

F. Power Strip

G. Power Strip Cover

H. Cord Holder

I. Bottle Opener

PARTS

2

TOOLS REQUIRED:

Phillips Head Screwdriver

HARDWARE INCLUDED:

HARDWARE

 

HARDWARE INCLUDED:

M4x12 Screw (Qty: 2)

M6x12 Screw (Qty: 52)

Screw Leveler (Qty: 4)

NOTE : 

             This equipment has been tested and found to 
comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against 
harmful interference in a residential installation. This 
equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful 
interference to radio communications.However, there 
is no guarantee that interference will not occur in 
a particular installation.
 
If this equipment does cause harmful interference to 
radio or television reception, which can be determined 
by turning the equipment off and on, the user is 
encouraged to try to correct the interference by one or 
more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and 

receiver.

 Connect the equipment into an outlet on a circuit 

different from that to which the receiver is connected.

 Consult the dealer or an experienced radio/TV 

technician for help.

 

NOTE : 

             This device complies with Part 15 of the FCC 
Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful 
interference, and (2) this device must accept any 
interference received, including interference that may 
cause undesired operation.  

 

NOTE: 16 of these screws are 

preattached to the Leg Panels.

NOTE: Levelers are preassembled to 

Leg Panels.

Содержание 76633 Butcher Block







Отзывы: