Craftsman 137.415030 Скачать руководство пользователя страница 13

Страница: 13 / 56

The adapter (Fig. 2) has a grounding

lug extending from it that MUST be

connected to a permanent earth

ground, such as a properly grounded

receptacle box.

In all cases, make certain the

receptacle is properly grounded. If

you are not sure, have a qualiﬁed

electrician check the receptacle.

overheating and burning out of the

motor. The table below shows the

correct size to use depending on cord

length and nameplate ampere rating. If

in doubt, use the next heavier gauge.

The smaller the gauge number, the

heavier the cord.

GUIDELINES FOR EXTENSION

CORDS

Make sure your extension cord is

properly wired and in good condition.

Always replace a damaged extension

cord or have it repaired by a qualiﬁed

technician before using it. Protect your

extension cords from sharp objects,

excessive heat and damp or wet areas.

This tool is for indoor use only. Do

not expose to rain or use in damp

locations.

This tool is intended for use on a

circuit that has a receptacle like the

one illustrated in Fig. 1. Fig. 1 shows

a three-pronged electrical plug and

receptacle that has a grounding

conductor. If a properly grounded

receptacle is not available, an adapter

(Fig. 2) can be used to temporarily

connect this plug to a two-contact

grounded receptacle.

MINIMUM GAUGE FOR EXTENSION CORDS (AWG)

(When usng 120 volts only)

Ampere Rating

Total length of Cord

More Than Not More Than 25ft. 50ft. 100ft. 150 ft.

(7.62 15.24 30.48 45.72 m)
AWG- American Wire Gauge

0 6

18 16 16 14

6 10

18 16 14 12

10 12

16 16 14 12

12 16

14 12 Not Recommended

WARNING

CAUTION



Three-Pronged Plug

Grounding Prong

Properly Grounded

Three-Pronged Receptacle

Fig. 1

Fig. 2

Grounding Lug

Make sure this

is connected

to a known

ground.

Two-Pronged

Receptacle

Adapter

Содержание 137.415030

























































Результаты поиска

Содержание 137.415030

Отзывы:

Похожие инструкции для 137.415030

Бренды по названию

Популярные бренды

Craftsman 137.415030, Руководство оператора

Результаты поиска

Содержание 137.415030

Отзывы:

Похожие инструкции для 137.415030

Бренды по названию

Популярные бренды