background image

page 9

Remove 3 screws from switch housing cap. 

If you wish to use fan WITHOUT the light kit

align holes in switch housing cap with holes in 
switch housing. Use screws that were just 
removed to attach switch housing cap to switch 
housing. 

Please proceed to Section 11 on page 10 to 

complete installation WITHOUT the light kit.

If you wish to use fan WITH the light kit

,

 

punch 

center cap out of switch housing cap with a 
screwdriver.

IMPORTANT

: Any light kit purchased for use with 

this fan 

MUST be CETL/ETL 

(or CUL/UL)

 

APPROVED for WET LOCATION or OUTDOOR 
USE.

Locate 

BLACK

 (or 

BLUE

) and 

WHITE

 wires in 

switch housing labeled LIGHT. Remove and 
discard plastic that holds these 2 wires together.

Remove hex nut and lock washer from threaded 
rod at top of light kit fitter. Gently feed wires (one 
by one) from light kit fitter through center hole in 
switch housing cap and then screw switch 
housing cap onto threaded rod.

["Light Kit Assembly" continued on next page.]

10. Light Kit Assembly (Optional).

hex nut

lock washer

motor 
housing

switch housing

switch housing
cap

center cap

light kit fitter

9. Switch Housing Assembly.

Remove 1 screw from switch housing plate 
(on underside of motor) and loosen the 
other 2 screws.

Connect male plug from motor housing to 
female plug from switch housing. Be sure 
plugs connect completely.

Align slotted holes at top of switch housing 
with loosened screws in switch housing 
plate. Twist switch housing to lock. Re-insert 
screw that was just removed and securely 
tighten all 3 screws with a Phillips 
screwdriver.

switch housing

plate

male

plug

female

plug

motor housing

switch housing

threaded rod

switch housing

cap

Содержание Riverfront























Отзывы: