background image

PWLI1903

page 12

Problem: 

Fan fails to operate.

Solutions:

1. Check wall switch to fan/wall control.
2. Verify that wall control (optional use) is wired 
properly.
3. Check to be sure fan is wired properly.
4. Learning process between fan, remote control 
transmitter and wall control may not have been 
successful and code was not activated. Turn off power 
and repeat instructions for SET button in Section 11 
(page 10).
5. Check that red light on remote control transmitter 
turns on when a button is pressed indicating that the 
battery is good.
 

Problem: 

Light kit (optional) not lighting.

Solutions:

1. Check wall switch to fan/wall control.
2. Check that wires in canopy are wired properly.
3. 

Verify that molex connections in LED light kit are 

properly connected.

4. Learning process between fan, remote control 
transmitter and wall control may not have been 
successful and code was not activated. Turn off power 
and repeat instructions for SET button in Section 11 
(page 10).
 

Problem: 

Fan operates but light fails (if applicable) .

Solutions: 

1. Check to be sure wires in canopy are wired properly.
2. 

Verify that molex connections in LED light kit are 

properly connected.

 

Problem: 

Fan and light fail to operate with wall 

control and/or handheld remote control.

Solutions:

1. Check battery power in handheld remote control.
2. Learning process between fan, remote control 
transmitter and wall control may not have been 
successful and code was not activated. Turn off power 
and repeat instructions for SET button in Section 11 
(page 10).
3. If using optional wall control, check that battery in 
wall control is still good.

Problem: 

Fan wobbles.

Solutions:

1. Use the balancing kit in one of the hardware packs. 

If no blade balancing kit is provided, please call 
Customer Support, 1-800-486-4892, to request one.

2. Check to be sure set screw(s) on motor housing 
yoke is (are) tightened securely.
3. Check to be sure set screw on hanging ball is 
tightened securely.

Troubleshooting.

Warranty.

WARNING: 

Failure to disconnect power supply 

prior to troubleshooting any wiring issues may 
result in serious injury.

Parts Replacement.

For parts and information, please refer to
"Parts Inventory" on page 2.
Craftmade Customer Support:

1-800-486-4892

www.craftmade.com

CRAFTMADE™ LIFETIME LIMITED WARRANTY:
CRAFTMADE warrants this fan to the original household 
purchaser for indoor use under the following provisions:
1-YEAR WARRANTY: CRAFTMADE will replace or repair any 
fan which has faulty performance due to a defect in 
material or workmanship. Contact Craftmade Customer 
Service at 

1-800-486-4892 

to arrange for return of fan. 

Return fan, shipping prepaid, to Craftmade.  We will repair 
or ship you a replacement fan, and we will pay the return 
shipping cost.
5-YEAR WARRANTY: CRAFTMADE will repair or replace, at  
no charge to the original purchaser, any fan motor that fails 
to operate satisfactorily when failure results from normal 
use.
RETURN FAN MOTOR ONLY, shipping prepaid, to Craftmade 
Industries. We will repair or ship purchaser a replacement 
motor and Craftmade will pay the return shipping cost.
6-YEAR to LIFETIME LIMITED WARRANTY: CRAFTMADE will 
repair the fan, at no charge for labor only to the original 
purchaser, if the fan motor fails to operate satisfactorily 
when failure results from normal use. Parts used in the 
repair will be billed to the purchaser at prevailing prices at 
time of repair.
    The purchaser shall be responsible for all costs incurred 
in the removal, reinstallation and shipping of the product 
for repairs.
    This warranty does not apply when damage from 
mechanical, physical, electrical or water abuse results in 
causing the malfunction. Deterioration of finishes or other 
parts due to time or exposure to salt air is specifically 
exempted under this warranty.
    Neither Craftmade nor the manufacturer will assume any 
liability resulting from improper installation or use of this 
product. In no case shall the company be liable for any 
consequential damages for breach of this, or any other 
warranty expressed or implied whatsoever. This limitation 
as to consequential damages shall not apply in states 
where prohibited.

Содержание MOD60



























Отзывы: