background image

3. Installation Preparation.

4. Hanging Bracket Installation.

ON

OFF

ON

OFF

Turn off circuit breakers to current fixture from 
breaker panel and be sure operating light switch is 
turned to the OFF position.
WARNING: Failure to disconnect power supply prior to 
installation may result in serious injury.

Remove existing fixture. 
WARNING: When using an existing outlet box, be sure 
the outlet box is securely attached to the building 
structure and can support the full weight of the fan. 
Ensure outlet box is clearly marked "Suitable for Fan 
Support." If not, it must be replaced with an approved 
outlet box. Failure to do so can result in serious injury.

CAUTION: Be sure outlet box is properly grounded and 
that a ground (GREEN or bare) wire is present.

Install hanging bracket to outlet box using original 
screws, spring washers and flat washers provided 
with new or original outlet box.If installing on a 
vaulted ceiling, face opening of hanging bracket 
towards high point of ceiling. Arrange electrical 
wiring around the back of the hanging bracket.

*Note: It is very important that you use the proper 
hardware when installing the hanging bracket as this 
will support the fan. 

Vaulted ceiling 
angle is not to 
exceed 25 degrees.

downrod

installation

flushmount

installation

7 feet

(2.13 m) (76 cm)

30 

inches

blade edge

To prevent personal injury and damage, ensure 
that the hanging location allows the blades a 
clearance of 7 feet (2.13m) from the floor and 
30in. (76cm) from any wall or obstruction. 
This fan is suitable for room sizes up to 
400 square feet (37.2 square meters).

Installation requires these tools:
Phillips screwdriver, flathead screwdriver, 
adjustable pliers or wrench, stepladder, wire 
cutters, and rated electrical tape.

This fan can be mounted with a downrod on a 
regular (no-slope) or vaulted ceiling.  The 
hanging length can be extended by purchasing 
a longer downrod (0.5in./1.27cm diameter). 
Other installation, such as flushmount, is not
available for this fan.

hanging bracket

spring washers

outlet box screws

flat washers

page 4

12f

t. - 20f

t.

12ft. - 20ft.

(3.66m - 6.1m)

(3.66m - 6.1m)

Содержание Manning MNG52













Отзывы: