manualshive.com logo in svg

Craftex TENONING JIG, Руководство пользователя, Страница: 8 / 16

Поделиться
Скачать
Craftex TENONING JIG Скачать руководство пользователя страница 8

8

3. Remove Tenoning Jig from machine and place it

upside down.

4. Using the 2.5mm allen wrench (not shown), adjust

screws (C), clockwise to eliminate play, or counter-

clockwise to provide a looser fit between the guide

bar and miter slot. See 

Figure 8

.

5. Insert the Tenoning Jig back into the miter slot of

the table saw. Recheck the fit by sliding miter gage

back and forth to determine if there is any side-to-

side play. If more adjustments are needed, repeat

Steps 3, 4 and 5.

ALIGNING TENONING JIG

DISCONNECT SAW FROM THE POWER SOURCE.

1. Place the Tenoning Jig guide bar (A) into the left

miter gage slot (D). See 

Figure 9

.

2. Using a square (E), check that the vertical work

support plate (F) is 90 degrees to the table surface.

If an adjustment is necessary, loosen lock handle

(G), move vertical work support plate until it is

90 degrees to the table surface and tighten lock

handle. 

NOTE:

The lock handle is spring-loaded

and can be repositioned by pulling out on the

handle and rotating the handle clockwise or

counterclockwise. See 

Figure 9

.

Fig. 10

H

F

3. With the vertical work support plate (F) adjusted at

90 degrees to the table surface, tighten positive

stop setscrew (H) until it bottoms. This positive 

stop setscrew enables you to rapidly reposition

the vertical work support plate to 90 degrees.

See 

Figure 10

.

Fig. 11

S

4. Using a square (E) check that the face of the back-

stop (J) is 90 degrees to the table surface. If an

adjustment is necessary, loosen lock lever (K),

adjust backstop accordingly and retighten lock

handle. 

NOTE:

The lock handle is spring-loaded

and can be repositioned by pulling out on the handle

and rotating the handle clockwise or counterclock-

wise. When the backstop is 90-degrees to the table,

adjust the setscrew (S) until it touches the back-

stop.  Tighten the jam nut. Setscrew (S) acts as a

positive stop and allows you to quickly position the

backstop back to the 90-degree position after it has

been tilted. See 

Figure 11

.

J

K

E

Fig. 12

5. Loosen nut (L) and turn setscrew (M) counterclock-

wise two or three turns. See 

Figure 12

.

L

M

WARNING

!

WARNING

!

This jig should only be used with suitable tablesaws. Please refer to your tablesaw’s manual for further information. All 

tablesaw safety features and guards must be kept in place and in good working order during the use of this jig.

Содержание TENONING JIG

















Отзывы:

Нет отзывов