Craftex CT073 Скачать руководство пользователя

Страница: 3 / 30

GENERAL SAFETY INSTRUCTIONS

EXTREME CAUTION SHOULD BE USED IN OPERATING ALL POWER TOOLS. KNOW

YOUR POWER TOOL, BE FAMILIAR WITH ITS OPERATION. READ THE OWNER’S

MANUAL AND PRACTICE SAFE USAGE PROCEDURES AT ALL TIMES.

CONNECT

your machine

ONLY

to the matched and specified power

source.

WEAR SAFETY GLASSES, RESPIRATORS, HEARING PROTECTION

and

SAFETY SHOES

when operating heavy machinery.

Always wear

safety glasses.

DO NOT

wear loose clothing or jewellery when operating machinery.

A Safe Environment is important

. Keep the area free of dust, dirt and

other debris in the immediate vicinity of the machine.

BE ALERT

! Do Not Use prescription or other drugs that may affect your

ability or judgement to safely use this machine.

DISCONNECT

the power source making other adjustments or repairs.

NEVER

leave an operating tool unattended.

NEVER

reach over the table when the tool is in operation.

ALWAYS

keep blades, knives or bits sharp and properly aligned.

ALWAYS

keep all safety guards in place and ensure their proper function.

ALWAYS

use push sticks and featherboards to safely feed your work

through the machine.

ALWAYS

make sure that any tools used for adjustments are removed

before operating the machine.

ALWAYS

secure your work with the appropriate clamps or vises.

ALWAYS

keep bystanders safely away while operating machinery.

THINK SAFETY. WORK SAFELY.

Never attempt a procedure if it does

not feel safe or comfortable.

Содержание CT073































Результаты поиска

Содержание CT073

Отзывы:

Похожие инструкции для CT073

Бренды по названию

Популярные бренды

Craftex CT073, Руководство пользователя

Результаты поиска

Содержание CT073

Отзывы:

Похожие инструкции для CT073

Бренды по названию

Популярные бренды