Craden DP6 Скачать руководство пользователя страница 7

Страница: 7 / 62

3.3.2 DP7 Ribbon Cartridge Loading/Replacement

To replace a DP7 ribbon cartridge:

1. If the new cartridge has a plastic ribbon shield attached, remove it.

2. Pull about a 1/2" loop of ribbon from the new cartridge.

3. Remove the lid. If several minutes of continuous printing have just been finished, the printhead and

carriage may be hot to the touch. Avoid contact with those parts.

4. Press the



A and



B keys simultaneously to position the printhead nose between two

drive roller

segments.

5. Lift the carriage shaft with a little finger. Remove the old cartridge by pressing the side clips while pulling

the old cartridge forward.

6. Push the metal ribbon shield downward. Guide the new cartridge's ribbon loop around the pivoting slider

and under the printhead nose.

7. Locate the cartridge tips behind the pivoting slider.

8. Move the cartridge toward the carriage and rotate the cartridge knob counter-clockwise until the cartridge

seats on the carriage plate.

9. Insure that the ribbon lies flat against the printhead nose and that both metal side clips lock onto the

cartridge tabs.

3.4 KEYPAD OPERATION

EJECT: ejects an inserted document if the print buffer is empty.

Drive Knob

Side Clips

Cartridge Tip

Ribbon Shield

Printhead Nose

Carriage Shaft

Pivoting Slider

DP7 RIBBON CARTRIDGE LOADING

Содержание DP6































































Результаты поиска

Содержание DP6

Отзывы:

Похожие инструкции для DP6

Бренды по названию

Популярные бренды

Craden DP6, Технические характеристики

Результаты поиска

Содержание DP6

Отзывы:

Похожие инструкции для DP6

Бренды по названию

Популярные бренды