Craden DP6 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 62

background image

12

3.6.4 Override Parameters

Press 9 9 then FUNCT to display the following Override Parameters. Changes should be made only by
trained personnel.

DISPLAY

REMARKS

LOCKED or UNLOCKED

LOCKED allows parameters to be displayed but not changed.
UNLOCKED allows parameters to be changed by the



A key.

COVER OVERRIDE OFF or
ON

OFF requires the cabinet lid to be closed for printing to occur. ON
allows trained personnel to print with the lid removed. Replacing the lid
automatically sets the override OFF.

3.6.5 Automatic Alignment Parameters

The following printer parameters may be selected at the end of the Printer Parameter (9 2 FUNCT)
menu on printers with the automatic alignment feature:

DISPLAY

REMARKS

SKEW DETECTION =
CORRECT SKEW, DETECT
SKEW, or IGNORE

select CORRECT SKEW to automatically align skewed documents,
DETECT SKEW to detect but not align skewed documents, or
IGNORE to disable both skew detection and correction.

SKEW DETECTION ALLOWED
= .030, .050, .080, .110 or .130

Select the maximum skew per 4 inches of document width. Treatment
of documents with excess skew is set by the next parameter.

IF

FORM

SKEWED

=

ENTER/EJECT

KEYS

or

AUTOMATIC EJECT

If a document has excess skew, ENTER/ EJECT KEYS will continue
printing if ENTER is pressed or eject the document if EJECT is
pressed. AUTOMATIC EJECT will always eject a document with
excess skew

IF NARROW FORM =
PROCEED or ENTER/EJECT
KEYS

Documents less than 4.5 inches wide will be detected as skewed.
PROCEED will always accept the document, ENTER/EJECT KEYS will
continue printing if ENTER is pressed or eject the document if EJECT
is pressed.

3.7 DIAGNOSTICS

3.7

.1 Power Up Diagnostics

Diagnostic routines are automatically executed during power-up. If a fault is detected, ROM TEST BAD
or RAM TEST BAD may be displayed. If a fault occurs, press



A to advance to the next test. However,

the printer should not then be operated. If the problem is not a POWER FAILURE (see 3.10.1), contact
your Service Personnel or see 5.6 of the Technical Manual for troubleshooting.

3.7.2 Enhanced Diagnostics

Diagnostics may be executed by pressing 9 0 then FUNCT. If no faults exist, PROM REVISION

XX,

ROM TEST OK and RAM TEST OK will be displayed. If a fault exists, "BAD" will be displayed instead of
"OK" until



A is pressed to advance to the next test.

After RAM TEST XXX is displayed, SENSORS LFBC will be displayed. L is the left home carriage sensor; F
and B are the front and back document sensors and C is the cover open sensor. Any sensor that is covered
will have its corresponding indicator erased. Each sensor may be activated to check for proper operation.
Press



A to conclude this test.

«
...
10
11
12
13
14
...
»

Содержание DP6































































Отзывы:

Нет отзывов

Похожие инструкции для DP6

Бренд: QMS Страницы: 86

Бренд: Saxxot Страницы: 13

Бренд: Canon Страницы: 542

Бренд: TRENDnet Страницы: 14

Magicolor 4650DN

Бренд: Konica Minolta Страницы: 260

Allen-Bradley ClearMark

Бренд: Rockwell Automation Страницы: 16

Бренд: Star Micronics Страницы: 127

Бренд: Canon Страницы: 776

Бренд: Bang & Olufsen Страницы: 4

Бренд: Panasonic Страницы: 6

Desktop Unit XX-XXXX

Бренд: Panasonic Страницы: 51

Бренд: Panasonic Страницы: 65

Бренд: Panasonic Страницы: 172

Бренд: Panasonic Страницы: 166

Бренд: Panasonic Страницы: 194

Бренд: Panasonic Страницы: 262

Бренд: Panasonic Страницы: 296

Бренд: Panasonic Страницы: 375

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды