CP CP-D4 Скачать руководство пользователя страница 10

CP-Instruments 

www.cp-instruments.pl / [email protected]

tel. 71 798-57-84

5. Modes & Functions

Normal mode 

The main measuring method of  CP-D4 meter is Normal mode. In this setting the measured value 

is refreshed continuously

Max. Hold

 

If the measured area is not easily reachable and it is impossible to read the value while measuring, 

the Max. Hold mode may be used. After choosing that mode the measured value is not refreshed 

continuously. The meter will show only the highest value gained from numerous measurements.

Caution:

 Even single touching of sensor plate or electrodes during this mode will cause a highly inaccurate 

outcome. That in turn will result in the need of repeating the whole measurement process. The measurement 

in that set may be repeated by switching the mode into Normal and then into Max. Hold again.

Auto power off

To extend the battery life, the moisture meter is equipped with an automatic switch off function 

that is activated 12 minutes after switching on the device. This function is always active and it 

cannot be turned off.

Service Info

This mode enables to check some meter service information which include:

• total working time,

• quantity of switching-on,

• software version,

• date of production,

• batteries voltage.

 

This mode may be accessed by pressing and holding the SET button for 5 seconds and then by pressing 

ON/HOLD button simultaneously. All the information will be shown as long as the SET button will be 

held.

6. Power supply

CP-D4 meter is battery powered. It uses 2 AA type batteries. Both, rechargeable and standard 

batteries may be used. Battery status shows the remaining capacity of the batteries. If the curren

-

tly used batteries are almost out of charge, the battery icon will show empty.

While changing batteries into new ones both batteries should be replaced. Replace only with 2 of the same 

type of batteries and only fully charged ones.

Battery arrangement scheme is shown in the picture below:

Содержание CP-D4


















Отзывы: