background image

PILOT ADJUSTMENT

Locate the pilot adjustment screw on the valve.  The pilot
flame should surround at least the top 3/8” of the powerpile
(pilot generator) or thermocouple (see below).  The pilot is
unregulated so it will be operating at inlet line pressure (Max.
7” w.c. for natural gas and 11” w.c. for propane).  To decrease
the pilot flame, turn the screw clockwise (approximately seven
to nine full turns to bottom of pilot light channel) until you
produce sufficient flame at the minimum noise level.

PILOT FLAME ADJUSTMENT

3/8 TO 1/2 INCH

PILOT FLAME SHOULD ENVELOP 3/8 TO 1/2 INCH

OF THE TIP OF THE GENERATOR.

MAINTENANCE INSTRUCTIONS

1.

Installation and repair should be done by a qualified
service person.  The appliance should be inspected before
use and at least annually by a professional service person.
More frequent cleaning may be required due to excessive
lint from carpeting, bedding material, etc.  It is
imperative that control compartments, burners, pilot
burners, circulating air passageways and venting systems
of the appliance be kept clean.

2.

If the appliance has been equipped with the optional
WFF81-C fan kit assembly, the bearings of the motor
should be oiled every six months with approximately 2
drops of  S.A.E. 20 oil.

3.

The appliance area must be kept clear and free of any
combustible materials, gasoline and other flammable
vapors and liquids.

4.

It is essential that the flow of combustion and ventilation
air not be obstructed.

5.

Periodic examination of the entire ventilation system as
a routine part of the safety performance check is
recommended on an annual basis.

BURNER FLAME ADJUSTMENT - STAINLESS STEEL BURNER

1.  

FLAME TOO SOFT

 - Yellow

2.  

FLAME TOO HARD

 - Deep Blue

3.  

NORMAL FLAMES

     Flame.  Open air shutters until

    Coloration.  Closing air shutters

    yellow tipping disappears.

    to a point where yellow tipping
    begins, re-open slightly to
   eliminate yellow tipping.  Air
    shutter adjustment is now correct.

NOTE:  It is advised that the burner flames be checked at least twice during the heating season for any changes in burner
characteristics.  Vacuum burner compartment at start of heating season or as often as needed.

Page 12

   Air
Shutter

1

2

3

Содержание W255F and

























Отзывы: