background image

LIMITED WARRANTY

The Louisville Tin & Stove Co. warrants to 

the original user the accompanying product for the 
period specified herein, provided said product is 
installed, operated, maintained, serviced, and used 
according to the instructions and specifications 
accompanying the product.   

AS OUTLINED IN 

OUR INSTRUCTIONS, ANY WARRANTY 
CONSIDERATIONS ARE CONTINGENT ON 
INSTALLATION BY A QUALIFIED 
INSTALLER (CONTRACTOR).  SELF-
INSTALLATION IS PROHIBITED AND WILL 
INVALIDATE YOUR WARRANTY. 
 

If within a period of one year from the date 

of installation of the product, any part supplied by the 
manufacturer proves to be defective due to 
workmanship or material, it will replace such part, 
provided parts have not been subjected to misuse, 
alteration, neglect, or accidents.  The term of the 
warranty for the heat exchanger and burners is covered 
in Table A below.  Any claim not made within ten 
(10) days after the expiration of the warranty period 
shall be deemed waived by the user. 
 

The manufacturer shall have no liability or 

be required to perform any obligation under this 
warranty unless, when requested, the user returns, at 
the user’s expense, the component or product claimed 
defective, to the manufacturer for inspection, to enable 
the manufacturer to determine if the claimed defect is 
covered by this warranty. 
 

No charges for freight, labor or other 

expenses incurred in the repair, removal, or 
replacement of any product or component claimed to 
be defective, will be paid by the manufacturer to the 
user, and the manufacturer will not be liable for any 
expenses incurred, by the user, in remedying any 
defect in the product. 
 

Service under this warranty is the 

responsibility of the installer.  In the event service 
under this warranty is needed, the user of the product 

shall request such service directly from the installer.  
If the user is unable to locate the installer, the  user  
should write directly  to  the manufacturer, and the 
name of an alternative service source will be supplied. 
 

The product safety registration card (packed 

inside the appliance) must be completed and returned 
to the factory. 
 

THIS WARRANTY IS EXPRESSLY IN 

LIEU OF ANY OTHER WARRANTIES, EXPRESS 
OR IMPLIED (WHETHER WRITTEN OR ORAL).  
ANY IMPLIED WARRANTY OF 
MERCHANTABILITY OR OF FITNESS FOR A 
PARTICULAR PURPOSE IS EXPRESSLY 
LIMITED TO THE DURATION OF THE 
MANUFACTURER’S EXPRESS, WRITTEN 
WARRANTY. 
 

UNDER NO CIRCUMSTANCES SHALL 

THE MANUFACTURER BE LIABLE FOR ANY 
SPECIAL, INDIRECT OR CONSEQUENTIAL 
DAMAGES OR EXPENSES ARISING DIRECTLY 
OR INDIRECTLY FROM ANY COMPONENT OR 
FROM THE USE THEREOF.  THE REMEDIES SET 
FORTH HEREIN SHALL BE THE EXCLUSIVE 
REMEDIES AVAILABLE TO THE USER AND 
ARE IN LIEU OF ALL OTHER REMEDIES. 
 

SOME STATES DO NOT ALLOW 

LIMITATIONS ON HOW LONG AN IMPLIED 
WARRANTY LASTS, SO THE ABOVE 
LIMITATIONS MAY NOT APPLY TO YOU. 
 

SOME STATES DO NOT ALLOW THE 

EXCLUSION OR LIMITATION OF INCIDENTAL 
OR CONSEQUENTIAL DAMAGES, SO THE 
ABOVE LIMITATIONS OR EXCLUSIONS MAY 
NOT APPLY TO YOU. 
 

THIS WARRANTY GIVES YOU 

SPECIFIC LEGAL RIGHTS, AND YOU MAY 
ALSO HAVE OTHER RIGHTS, WHICH VARY, 
FROM STATE TO STATE. 

 
 
 

 
 
 

 
 

 
 
 

 
 

 

LOUISVILLE TIN & STOVE COMPANY 

737 S. 13

TH

 STREET  -  LOUISVILLE, KY. 40210 

TABLE A 

 

 

 

 

 

 

 

 

          

Warranty Period 

Product   

 

 

 

 

 Heat 

Exchanger/Tubes Burners 

Cozy Gas Fired Floor Furnace 

 

 

 

 

10 Years   

10 Years 

Cozy 

Gas 

Fired 

Wall 

Furnace 

     10 

Years 

 10 

Years 

Cozy Gas Fired Vented Console Heater  

 

 

 

10 Years   

10 Years 

Cozy Gas Fired Direct Vent Heater 

 

 

 

 

10 Years   

10 Years 

Cozy Gas Fired Counterflow Furnace   

 

 

 

10 Years   

10 Years 

Cozy Gas Fired Counterflow Direct Vent Furnace 

 

 

10 Years   

10 Years 

Cozy Gas Fired Mobile Home Direct Vent Furnace 

 

 

10 Years   

10 Years 

Cozy Gas Fired Hi-Efficient Direct Vent Wall Furnace 

 

 

10 Years   

10 Years 

Cozy Gas Fired Direct Vent Baseboard Heater 

 

 

 

10 Years   

10 Years 

Cozy Fan-Type, Direct Vent Through-The-Wall Gas Heater 

 

10 Years   

10 Years 

Cozy Blue Flame Vent Free Heater 

 

 

 

 

N/A 

 

10 Years 

Cozy Infra-Red Vent Free Heater 

 

 

 

 

N/A 

 

N/A 

Содержание W255F and

























Отзывы: