Covaris ML230 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 46

Covaris ML230 Скачать руководство пользователя страница 6

6

Covaris

Part Number: 010516 Rev B | March 2020

ML230 Setup & Instruction Manual

1.1 Overview of the User Manual

This manual contains the installation, operation, and service instructions for the ML230 Focused-ultrasonicator which are essential
to the proper use and care of this equipment. Should any unforeseen problems occur with the normal operation of the equipment,
contact Covaris Technical Support (

[email protected]

) immediately.

The following definitions apply in this manual:

1.2 The ML230 and the Covaris Process

The ML230 Focused-ultrasonicator is based on Covaris Adaptive Focused Acoustics (AFA) technology. This instrument is designed to
provide researchers an integrated stand-alone tool to be used in laboratory environment. The instrument is ideal for those who work
with DNA shearing and sample preparation.

The system is comprised of the

Treatment System

which delivers the acoustic energy to the sample, the

Safety System

which protects

users from inadvertently contacting the high intensity acoustic energy, and an embedded

Computer and Application Software

which

provides users an interface to control the device.

The Covaris Process

uses Adaptive Focused Acoustic energy to precisely control cavitation and acoustic streaming within the sample

treatment vessel in a non-contact, isothermal fashion. Focused acoustic energy is generated and delivered to individual samples. The
mechanical energy imparted on the sample results in a controlled series of compression and rarefaction events.

1. Introduction

NOTE:

Informational.

CAUTION:

Equipment damage may occur.

WARNING:

Personal injury may occur.

«
...
4
5
6
7
8
...
»

Содержание ML230















































Отзывы:

Нет отзывов