Covaris ML230 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 46

Covaris ML230 Скачать руководство пользователя страница 2

2

Covaris

Part Number: 010516 Rev B | March 2020

ML230 Setup & Instruction Manual

UNIVERSAL PRECAUTIONS

Universal Precautions should be followed on all specimen samples, regardless of whether a sample is known to contain
an infectious agent. Laboratories handling specimen samples are advised to comply with applicable parts of the following
government and clinical standards, or their equivalent in the country of use:

• Centers for Disease Control (CDC), Universal Precautions for Prevention of Transmission of HIV and Other Bloodborne

Infections, published 1987, updated 1996

• Clinical and Laboratory Standards Institute (CLSI), GP17-A2 Clinical Laboratory Safety; Approved Guideline - Second

Edition, published 2004, ISBN 1-56238-530-5

• Clinical and Laboratory Standards Institute (CLSI), M29-A3 Protection of Laboratory Workers from Occupationally

Acquired Infections; Approved Guideline, Third Edition, published 2005, ISBN 1-56238-5674

• Occupational Safety and Health Administration (OSHA), 29 CFR 1910.1030 Bloodborne Pathogens

• International Standards Organization (ISO) 15190:2003, Medical Laboratories – Requirements for Safety

Trademarks

Patented or patent pending and registered or registration-pending trademarks of Covaris are protected.

Registered names and trademarks used in this document, even when not specifically marked as such, are not to be considered
unprotected by law.

WCS and AFA are either registered trademarks or trademarks of Covaris, Inc. in the United States and/or other countries.

Teflon is a registered trademark of The DuPont Company.

Information subject to change without notice
For Research Use Only (RUO)
Not for use in Diagnostic Procedures
Publication PN 010516
Product covered by Patent No. US6, 719,449, US6, 948,843, and other pending applications
2020© Covaris Inc., All Rights Reserved

Covaris, Inc.
14 Gill Street, Unit H
Woburn, Massachusetts
01801-1721 USA

«
1
2
3
4
...
»

Содержание ML230















































Отзывы:

Нет отзывов