background image

31

31

31

Step 15:
Hook the suspension springs (#31) into the top 
of both holes of the swing arm tubes (#15). 
Repeat the same procedure for both sides. 
See Fig. H.

Step 16:
Hang the opposite ends of the suspension 
springs (#31) into the holes located on the 
angled braces of the top cross beam 
w/adjustable teeth (#1). 

Repeat the same 

procedure for both sides. 

See Fig. I.

 

To assure stability, double check that all of 
the bolts have been completely tightened 
and cover them with bolt caps (#34, #35, 
and #36).

PAGE 7 OF 8

Fig. H

Fig. I

STOP     DON’T RETURN TO STORE!

31

15

15

15

15

1

31

31

Special Warnings

1. The user of this swing should always inspect it before each use.
2. It is essential to place this swing on level ground and not less than 6 feet away from any obstruction, such as
    fences, garages, houses, overhanging branches, laundry lines, or electrical wires.
3. Check the tightness of all of the nuts and bolts on a regular basis.
4. Make sure that the suspension springs are properly secured before each use.
5. Always remove the canopy in heavy wind conditions; otherwise the swing may tip over and cause damage to 
    its parts.
6. The manufacturer will not accept responsibility for unauthorized repairs or modifications to the swing or its parts.
7. Oil all of the metal parts that move regularly.
8. Weight limit is 700 lbs.

Cleaning and Maintenance

•  Wash frame and fabric parts with mild soap and water, rinse thoroughly, and dry completely. Do not use 

   bleach, acid, or other solvents on the frame or fabric parts.

•  We recommend the use of furniture covers when not in use.

•  Inspect and tighten all bolts and fasteners on a regular basis to ensure the proper performance and safety of 

   your swing.

•  In order to prolong the life and beauty of your 

swing, we recommend that it be stored in a dry and protected area 

   during off season periods.

Warning:
Make sure that both ends of the suspension
springs (#31) go completely through the holes 
in the angled braces on the top cross beam 
w/adjustable teeth (#1) and the swing arm 
tubes (#15).

1

Содержание RUS487W-WM









Отзывы: