CountyLine RBRC402CL Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 40

background image

28

REMOVING AND INSTALLING
DRIVELINE (SHEAR BOLT)

1. Disconnect driveline shield chain.
2. Bend back driveline shield cone.
3. Remove shear bolt and lock nut.
4. Push driveline onto input shaft toward

gearbox

and remove snap ring.
5. Pull driveline from gearbox shaft.
6. Replace or repair as necessary.
7. Install in reverse order of removal.

REPLACING DRIVELINE SHEAR BOLT

If shear bolt fails:

1. Bend back driveline shield cone.
2. If necessary remove sheared bolt with hammer

and punch and realign holes in yoke and shaft.
3. Replace with 1/2” x 3 1/2”

Grade 2 bolt

and

lock nut.

NOTE:

Driveline shield pulled back

for illustration purposes. Cutter drive

components are protected from shock loads

by a shear bolt.

SERVICE

IMPORTANT: Avoid shear bolt failure at start
up by engaging the PTO slowly at low engine
RPMs.

IMPORTANT:

Failure to use correct shear

bolt may damage gearbox and/or PTO

Shaft, thus voiding the warranty.

«
...
26
27
28
29
30
...
»

Содержание RBRC402CL









































Отзывы:

Нет отзывов

Похожие инструкции для RBRC402CL

Бренд: Hitachi Страницы: 158

Бренд: VersaLASER Страницы: 121

Бренд: Dahle Страницы: 9

Бренд: Olympia Tools Страницы: 2

PULVERISETTE 19

Бренд: Fritsch Страницы: 62

TopLine STANDARD 630 mm

Бренд: Kaufmann Страницы: 8

Classen SCHV-18/5.5

Бренд: Schiller Страницы: 16

Бренд: Ozito Страницы: 2

Бренд: YATO Страницы: 112

Бренд: PANDROL Страницы: 19

Go! baby 55600UG

Бренд: AccuQuilt Страницы: 8

Бренд: Makita Страницы: 80

Бренд: Makita Страницы: 44

Бренд: Makita Страницы: 80

Бренд: Rayjet Страницы: 83

Бренд: Larzep Страницы: 7

Бренд: Hitachi Страницы: 34

Бренд: Hitachi Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды