manualshive.com logo in svg

CountyLine 602377, Руководство по сборке и эксплуатации

Поделиться
Скачать
CountyLine 602377 Скачать руководство пользователя страница 3

Introduction

 3

602378 REV AA
12/18/2018

TABLE OF CONTENTS

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  2

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  3

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4

SAFETY RULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7

SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 9

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10

PRE-OPERATION CHECKLIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  13

OWNER SERVICE  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14

TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17

ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  19

BOLT TORQUE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  25

BOLT SIZE CHART & ABBREVIATIONS . . . . . . . . . . . . . . . . . . . . . . . . . .  26

GENERAL INFORMATION

■  

Some illustrations in this manual show the

digger with safety shields removed to provide a
better view. The digger should never be operated
with any safety shielding removed.

The purpose of this manual is to assist you in operating
and maintaining your post hole digger. Read it carefully.
It furnishes information and instructions that will help
you achieve years of dependable performance. These
instructions have been compiled from extensive field
experience and engineering data. Some information
may be general in nature due to unknown and varying

operating conditions. However, through experience
and these instructions, you should be able to develop
procedures suitable to your particular situation.

The illustrations and data used in this manual were cur

-

rent at the time of printing but, due to possible inline
production changes, your machine may vary slightly in
detail. We reserve the right to redesign and change the
machines as may be necessary without notification.

Throughout this manual, references are made to right
and left direction These are determined by standing
behind the equipment facing the direction of forward
travel.

WARNING

Содержание 602377





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды