manualshive.com logo in svg

CountyLine 602377, Руководство по сборке и эксплуатации

Поделиться
Скачать
CountyLine 602377 Скачать руководство пользователя страница 2

2 

Introduction

Gen’l (Rev. 12/18/2018)

TO THE OWNER:

Read this manual before operating your equipment. The information presented will prepare you to do a better and safer
job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become
acquainted with all adjustment and operating procedures before attempting to operate. Replacement manuals can be
obtained. Contact SpeeCo, Inc., 4909 SE International Way, Portland, OR 97222, or call 1-800-525-8322.

The equipment you have purchased has been carefully engineered and manufactured to provide dependable and
satisfactory use. Like all mechanical products, it will require cleaning and upkeep. Lubricate the unit as specified.
Observe all safety information in this manual and safety decals on the equipment.

Use only genuine SpeeCo service parts and SAE hardware. Substitute parts will void the warranty and may not meet
standards required for safe and satisfactory operation. Record the model number and serial number of your equipment
in the spaces provided:

Model:

_______________________________

Date of Purchase:

_____________________

Serial Number:

 (see Safety Decal section for location) ____________________________________

Provide this information to customer service to obtain correct repair parts.

Throughout this manual, the term 

NOTICE

 is used to indicate that failure to observe can cause damage to equipment.

The terms 

CAUTION, WARNING, 

and 

DANGER

 are used in conjunction with the Safety-Alert Symbol (a triangle with

an exclamation mark) to indicate the degree of hazard for items of personal safety.

Содержание 602377





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды