manualshive.com logo in svg

CountyLine 602377, Руководство по сборке и эксплуатации

Поделиться
Скачать
CountyLine 602377 Скачать руководство пользователя страница 13

Operation

 13

602378 REV AA
12/18/2018

SHEAR BOLT REPLACEMENT

Never replace shear bolt or auger retaining bolt

with a different length, or grade. Always use a
grade 2 bolt as a replacement.

Shear bolts are important for both safety and prevent

-

ing damage to the digger. Their intended function is to
break when too much force is applied.

Always replace shear bolts at the gearbox input with
manufacturer's part or one of the same size, length and

SAE

 

Grade 2

 specification.

Hardened bolts or bolts that are too long can cause
accidents resulting in injury or death.

The set screw, Figure 3, prevents the driveline from
coming off gearbox shaft if the shear bolt should shear.

 Figure 3

. Shear Bolt Replacement

PRE-OPERATION CHECKLIST

___ Review and follow all safety rules and safety

decal instructions on pages 5 through 9.

___ Check that all safety decals are installed and in

good condition. Replace if damaged.

___ Check that all shields and guards are properly

installed and in good condition. Replace if dam

-

aged.

___ Consult local utilities before digging. Know loca

-

tion of and avoid contacting all underground
cables, pipelines, overhead wires and other haz

-

ards in digging area.

___ Check that auger point and all cutting edges are

intact and in good repair.

___ Check that equipment is properly and securely

attached to tractor.

___ Make sure driveline spring-activated locking pin

slides freely and is seated firmly in tractor PTO
spline groove or gearbox PTO spline groove.

___ Set tractor PTO at correct rpm for your equip

-

ment.

___ Check all lubrication points and grease as

instructed in “Service, lubrication information.”

___ Lubricate all grease fitting locations. Make sure

telescoping PTO shafts and universal joints are
lubricated.

___ Check that all hydraulic hoses and fittings are in

good condition and not leaking before starting
tractor. Check that hoses are not twisted, bent
sharply, kinked, frayed or pulled tight. Replace
any damaged hoses immediately.

___ Make sure tractor 3-point lift links do not interfere

with hydraulic hoses or driveline throughout full
turning range.

___ Check that all hardware and cotter pins are prop

-

erly installed and secured.

___ Check attitude adjustment of auger.

___ Check and keep all bystanders 25 ft away from

equipment working area.

___ Before starting engine, operator must be in trac

-

tor seat with seat belt fastened. Place transmis

-

sion in neutral or park, engage brake and
disengage tractor PTO.

WARNING

1. Gearbox
2. Driveline
3. M6 x 25 set screw
4. M6 jam nut
5. 3/8 NC x 3 grade 2 shear bolt
6. 3/8 lock washer
7. 3/8 NC hex nut

*Input shield 
removed for detail

Содержание 602377





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды